cecotec CONGA ROCKSTAR 3000 ADVANCE ERGOWET Manual De Instrucciones página 25

ENGLISH
Suitable for dusting high cupboards, roofs, windows, corners, etc. Moreover, you can connect
the 2-in-1 narrow and wide accessories for furniture and corners and the extended brush.
Watertank accessory
With this accessory you will mop and scrub your floor just by attaching it to the vacuum cleaner.
Wall charging base installation
Fig. 10
1. Place the charging base on the wall and mark 3 spots to be drilled to fix the base. You
must take into account the height of the installation; it is important that vacuuming brush
head rests on the floor to avoid the charging base from holding all the vacuum cleaner's
weight.
2. Drill the 3 holes (previously marked) and insert the pegs and M4 x 32 mm screws.
3. Make sure that the charging base is securely fixed on the wall and place the vacuum
cleaner on the charging base by placing the vacuum cleaner charging terminals over the
charging base charging terminals (plastic tab).
4. Once the wall charging base is installed, connect the power adapter to the charging port,
and then you can charge the vacuum cleaner by simply sliding it up and down the wall
charging base. Fig. 11
Charge and display
- When the battery percentage is 20% or below, the device will automatically enter low
consumption mode. It is recommended to charge the vacuum cleaner when it reaches this
percentage.
- The battery must be charged with the charging base while it is connected to the main body.
Connect one of the ends of the power adapter to the power supply and the other to the
charging base. Fig. 11
- During charging, the charge light indicator will turn on red and the display will show the
current charge percentage. When the device is fully charged, the battery indicator will turn
green and the display will show 100%. Fig. 12
- You can also charge the battery without using the charging base. You can charge the
battery when the battery is installed or not in the vacuum cleaner. Connect the adapter and
connect the other end to the battery, paying attention to the direction. Once it is properly
connected, the charge light indicator will turn on red and will turn green once the charge
is complete. Fig. 13
5. WATERTANK ACCESSORY
- Do not use cleaning agents. Use clean and room temperature water only. Do not use the
vacuum cleaner to vacuum water.
48
- When the vacuum cleaner is not going to be used for a long period of time, remove the
water tank and empty the remaining water. Do not expose it to direct sunlight or to damp
environments.
Mop installation
- Place the mop cloth on the ground with the Velcro facing upwards.
- Align the mop cloth with the Velcro strips on the water tank and attach it without covering
the wheels. Fig. 14
Replacing the mop
- Remove the water tank from the vacuum cleaner.
- Use your foot to hold the accessory against the ground and pull the vacuum cleaner
upwards until both parts are separated.
- Replace the mop and refill the water tank.
- Install the water tank again, insert the tank in the lower part of the vacuuming brush head
and press until it is fixed.
Water emission
- When using this product for the first time, make sure the water tank lid is not fully open.
- When the product is not in use, check that the water release button and cap are closed, as
the product may continue to let out water if the water tank is full.
- To activate the water emission, the water emission push button must be pressed, and to
stop the water emission, the push button must be in the original position, as shown in
figure 15.
6. CLEANING AND MAINTENANCE
- Turn the appliance off, unplug it from the power socket, and allow it to cool down before
cleaning it.
- Use a soft, slightly dampened cloth to clean the device's surface.
- Never immerse the device in water or other liquids. Do not allow liquids to enter the device.
- Do not use sponges, powder products, or abrasive cleaning agents to clean the product.
- Do not leave the vacuum cleaner in a place with direct sunlight.
- Do not leave the vacuum cleaner in a wet place after cleaning it.
- After the brush has been used for a long time, bristles might start to tangle with hair and
other particles. Clean it for it to operate correctly again.
Filters and tank cleaning
- To prevent the appliance from overheating and losing suction power, it is suggested to
clean the filters frequently. To make the most of the suction power, it is suggested to clean
the filter after every use.
ENGLISH
CONGA ROCKSTAR 3000 ADVANCE ERGOWET 49