Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
maximum cleaning time, wait until the light turns into steady blue, as this indicates that
the battery is fully charged and that the robot vacuum cleaner is ready to clean.
Note
-
Take the robot vacuum cleaner to the charging base if the battery is low. The robot vacuum
cleaner may not turn on if battery is too low.
-
The robot vacuum cleaner will automatically turn on when placed on the charging base.
-
The robot vacuum cleaner cannot be turned off during recharge.
Installing the mixed tank. Fig. 8
-
Open the water-tank silicone lid and carefully fill up the tank while avoiding spillages.
Make sure the silicone clip is properly closed to avoid water from pilling. Never immerse
the tank in water or other liquids.
-
Install the mop on the mop bracket.
-
To install the tank on the robot vacuum cleaner, follow the direction shown in figure 8 and
manually press the tab and push it into the correct position. You will hear a click when it is
properly fixed.
-
Install the mop bracket following the direction shown in figure 8.
Recommendations:
-
It is not suggested to use the scrubbing function for the first-time use.
-
Do not use the mopping function if the robot vacuum cleaner is not being supervised.
-
To remove the mop bracket, press the release button and pull from it outwards.
-
Uninstall the mop bracket when the robot vacuum cleaner is charging or when not in use.
-
Add a few drops of cleaning agent to the water if necessary, as long as it is non-corrosive.
-
Using cleaning agents in excess might block water outlets.
-
In order to achieve perfect scrubbing, it is suggested to moisten the mop before using it.
First use
-
Once the robot vacuum cleaner and the charging base are installed, follow these steps
before the first cleaning.
-
First of all, fully charge the robot vacuum cleaner. It is suggested to allow the robot to
charge overnight. Once fully charged, it may carry out the first cleaning cycle and save
the first map. To do so, activate the Auto mode and select the Eco suction level. It is very
important to follow these instructions so that the robot vacuum cleaner recognises every
corner of your house and can carry out a complete mapping of it.
-
If your house is very large and the robot vacuum cleaner runs out of battery, it will return
to the charging base, save both complete and incomplete maps, and, once charged, it will
resume cleaning where it left off until the entire surface has been mapped. The robot
52
CONGA 7490 ETERNAL GENESIS
vacuum cleaner is constantly mapping, so it adapts in an individualised and personalised
way to the particularities of each house while constantly improving its map.
3. OPERATION
Robot vacuum cleaner's buttons
Auto Mode
-
Press the Start/Pause button on the robot vacuum cleaner or from the app for the robot
to automatically start cleaning in Edge mode and perform a cleaning cycle in an orderly
zig-zag pattern, while recognising which areas it has cleaned and which it hasn't. The
robot vacuum cleaner will automatically plan the cleaning route during cleaning.
-
If you control the robot vacuum cleaner manually during this mode, the robot will
recalculate the route, so it may pass through already cleaned areas. To ensure efficient
cleaning, do not operate the robot vacuum cleaner manually during automatic cleaning.
-
Thanks to its Total Surface 2.0 technology, if the battery is low during the cleaning cycle,
the robot vacuum cleaner will smartly return to the charging base automatically and, once
fully charged, it will resume the cleaning process from the same point.
-
During cleaning, the robot vacuum cleaner will stop briefly to evaluate the area and
calculate the cleaning route (this stop will vary depending on the house conditions).
Back Home mode
-
Press the Back Home button on the robot vacuum cleaner or from the app to send the robot
vacuum cleaner to the charging base. The robot vacuum cleaner will continue vacuuming
until it reaches the charging base.
-
This mode can be activated during any cleaning cycle.
-
The robot vacuum cleaner will take the shortest route back to the charging base thanks to
its map-memorisation feature and the smart back-home function.
-
Upon completing a cleaning cycle or when the battery is low, thanks to its TotalSurface
2.0 technology, the robot vacuum cleaner will automatically return to the charging base to
avoid running out of battery. Once the robot has recharged, it will resume cleaning from
the point it has stopped.
Note
:
If there is no good access to the charging base, the robot vacuum cleaner will not be able to
return to it. If this happens, place it manually on the charging base.
Functions
Pause:
While the robot vacuum cleaner is running, press the Start/Pause button on the robot vacuum
ENGLISH
53
CONGA 7490 ETERNAL GENESIS
Publicidad
