Descargar Imprimir esta página

Craftsman professional 351.217590 Manual Del Operador página 6

Publicidad

Idiomas disponibles

Idiomas disponibles

Craftsman 13"planer finishes r ough-cut lumber tosize and
planes s oft a ndhardwoods upto6"thick and13"wide. Wood
feeds i nto three-blade
cutterhead byrubber infeed/outfeed
rollers. Sturdy b ase construction
and four-post design p ermits
smooth f eeding a ndvirtually snipeless planing. Planer comes
withenclosed, universal ball b earing, 15Amp motor with
overload protection. Motor h asON/OFF s witch w ithremovable
key toprevent accidental start-up. Unit f eatures digital display,
two-speed feed system, depth-of-cut
gauge forconvenient
setup, workpiece thickness pre-set gauge with6settings for
consistent setup, easy hands-free replacement
ofblades f or
safety a nd minimized
downtime,
built-in dust collector, top mount-
edrollers forworkpiece
return, built-in c arrying handles, cord
wrap forportability andfolding i nfeed/outfeed
tables w ithrollers
forsmooth o peration. Planer takes c utsupto3/32" perpass at
either 11or22feet p erminute. Inch height scale has graduations
in_/_" i ncrements,
andmetric h eight scale hasgraduations
in
lmmincrements.
(Requires four Cbatteries, notincluded.)
SPECIFICATIONS
Table S ize................................
13x 14W'
Extension Table S ize ........................
13x 12W'
Base Size.................................
25_/2 x15"
Workpiece
Width (max.) ...........................
13"
Workpiece
Thickness (max.) . .......................
6"
Maximum D epth o fCut ...........................
3/32"
Cuts Per Minute ..............................
24,000
Feed Rate...............................
11/22 FPM
Overall Dimensions
................
21"Hx27"Wx39"D
Weight . ....................................
106 Ibs
OPERATION S AFETY
RULES
WARNING:
For your own safety, read all of the instructions
and precautions before operating tool.
WARNING:
Operation of any power tool can result in foreign
objects being thrown into eyes which can result in severe eye
damage. Always wear safety goggles complying with United
States ANSI Z87.1 (shown on package) before commencing
power tool operation.
CAUTION:
Always observe the following safety precautions:
Know general power tool safety. Make sure all precautions
are understood (see pages 2 and 6).
Whenever adjusting or replacing any parts on planer, turn
switch OFF and remove plug from power source.
°
Make sure all guards are properly attached and securely
fastened.
Make sure all moving parts are free from interference.
Always wear eye protection or face shield.
°
Make sure blades are aligned and properly attached to
cutterhead.
°
Do not plug in planer unless switch is in OFF position.
After turning switch on, allow planer to come to full
speed before operating.
°
Keep hands clear of all moving parts.
°
Do not force cut. Slowing or stalling will overheat motor.
Allow automatic feed to function properly.
*
Use quality lumber. Blades last longer and cuts are
smoother with good quality wood.
Do not plane material shorter than 15", narrower than 3/,,,
wider than 13" or thinner than W'.
Never make planing cut deeper than 3/32".
Maintain the proper relationships of infeed and outfeed
table surfaces and cutterhead blade path.
Do not back the work toward the infeed table.
Take precautions against kickback. Do not permit anyone
to stand or cross in line of cutterhead's
rotation. Kickback
or thrown debris will travel in this direction.
Turn switch off and disconnect power whenever planer is
not in use.
Replace blades as they become damaged or dull.
Keep planer maintained. Follow maintenance instructions
(see pages 9-12).
OPERATING
CONTROLS
ON/OFF SWITCH
Refer to Figure 11.
The ON/OFF switch is located on the front of the planer
motor. To turn the planer ON, lift switch cover and move the
switch to the up position. To turn the planer OFF, move the
switch to the down position by pushing down on the switch
cover.
CIRCUIT BREAKER
Refer to Figure 11.
The planer is equipped with a motor protection device-circuit
breaker. The breaker will automatically
shut the planer off
when excessive current is consumed.
If the breaker is tripped, turn the planer off and reset the
circuit by pressing the button.
CAUTION:
Be sure to turn the planer off prior to resetting
the circuit breaker to avoid unintentional start-up of the planer.
ON/OFF Switch
Figure 11 - ON/OFF Switch and Circuit Breaker
NOTE: Switch cover has been removed for illustration.
SWITCH LOCK
Refer to Figure 12, page 7.
The planer can be locked from unauthorized
use by locking
the switch. To lock the switch:
*
Turn the switch to OFF position and disconnect planer
from power source.
.
Pull the key out. The switch cannot be turned on with the
key removed.
NOTE: Should the key be removed from the switch at the ON
position, the switch can be turned off but cannot be turned on.
.
To replace key, slide key into the slot on switch until it snaps.
6

Publicidad

loading