GE Profile GXCF25FBS Manual Del Propietário página 4

Using the water dispenser.
Features and Parts List
0 Bottle Support Collar--Black (WS28X10048)
Separator (WS28X10013)
Cold Water Tank
Hot (Red) and Cold (Blue) Power Switch (back of dispenser).
The CoM (Blue)
t)oxver sxvi|ch also ItlrllS Ol/Ihe
dliller
(omparHnenu
Indicator Lights. 'Ille green liglu will be li! x_r}_:l__1_(:dispenser
is t)lugged in. The red and l)lue lighls will (}cle on and off
while lilt?
(tisl)ens( r heals
alld cools lhe waler.
Comt)ressor
slarl is delayed u t) lo 3 mimnes,
Hot _ , Romn Temperature B, Cold I_ Water Dispenser
Buttons
Dispenser Drip Tray (WS28X10031) and Grille (WS28X10032)
O Cmnpartment Drip Tray (WS29X10029)
_Chiller Compartment. The (omt)arlmenl is imended solel) for
use ill (hilling tanned and boxed l)exerages and packaged
nont)erishables.
Cmnpartment Shelf (WS28X10028)
Drainage Cap (WSOIXIO008)
Silicon Stopper (WSOIXIO007)
-----iiiiii\ _ _ ......
\' (\[,i
Loading the Dispenser and Start Up
Sanitize the dispenser water tanks prior to
installing a full bottle of water for the first time
(see "Cleaning and Sanitizing the Water Tanks").
IMPORTANT"Make sure the dispenser is
unplugged with both the hot and cold power
switches (on the back of the dispenser) set to the
0 (off) position. Before placing the water bottle on
the dispenser, wash hands and wipe the top of the
bottle with a clean cloth. Avoid touching the part
of the bottle that will be in contact with the water
dispenser.
Make sure the water /evel in the top of the
dispenser is low enough to allow for proper
bottle installation. Failure to do so may cause
the dispenser to overflow
1. Peel the label lh)m the top cover of the
bottle (i[prusent). Do notremove
the
entire 1)otth, cap.
2. Place the bottle on top of tile dist)enser
as shown, aligning the dispensing valve
t)robe to tile center of tile water bottle
cap. Press down umil the probe
t)enetrates the bottle cap, allowing the
bottle to rust on the sut)port collar:
3. IMPORTANT: Press both dispense buttm)s
m#il water runs from both taps.
4. Plug ill the dispense):
5. Set the COI,D and t lOT t)ower s_itches
(located on the top le/i rein" of the
dispenser) to the I (ml) position.
6. _llow 30 minutes fbr water to reach hot
and coM mmperatures.
Contact a local water bottle distributor to
purchase water bottles,
4
Child Safeguard
"Ihe tt()T disl)ens('r btlttOI/is equipped _dth
a chiM satbguard tl_at reduces die risk of hot
_;_mr being dispensed accidentally or t)} small
children. 'Ib dispense ware1; rotate the knob
com/terclockwise and push tl/e button ill. The
knoll will reset amomadcallx when the button
is released.
The dispenser heats water to a temperature of
approximately 190°F(88°C). Water temperatures
above 125°F(52°C) can cause severe bures or
death from scalding. Children, the disabled and
the elderly are at highest risk of being scalded.
CAUTION: Cbildre,lsbould be
supervised by a parent when using this product.