Publicidad
Idiomas disponibles
Idiomas disponibles
The undersigned manufacturer:
Via Invalidi del Lavoro, 1
37059 Santa Maria di Zevio (VR)
declares under its sole responsibility that the products
FLOOR SCRUBBING MACHINES
mod. Maxima 2017 55 BT - Maxima 2017 60 BT - Maxima 2017 50 BTO - Maxima 2017 50 BTS
comply with the provisions of Directives:
•
S.I. 2008/1597 Supply of Machinery (Safety) Regulations 2008 (as amended).
•
S.I. 2016:1091 Electromagnetic Compatibility Regulations 2016 (as amended).
The person authorized to compile the technical file:
Mr. Giancarlo Ruffo
Via Invalidi del Lavoro, 1
37059 Santa Maria di Zevio (VR) - ITALY
Santa Maria di Zevio (VR), 01/01/2018
This chapter lists the most common problems linked with the use of the machine. If you are unable to resolve the problems with the information given here, please contact your nearest assistance centre.
PROBLEM
The main switch is set to "0".
Check that, when switched on, there are no alarm
messages on the control display.
THE MACHINE DOES NOT
Make sure the batteries are correctly connected to
START
each other and that the battery connector is connected
to the electrical system connector.
Check the charge level of the batteries.
The plug on the battery charger cable is not correctly
inserted in the socket on the battery charger itself.
The plug on the battery charger power cable is not
THE BATTERIES ARE NOT
correctly inserted in the electrical outlet.
CHARGED CORRECTLY
(VERSIONS WITH BUILT-IN
The characteristics of the mains power supply do not
BATTERY CHARGER)
correspond to those required by the battery charger.
The LEDs of the battery charger blink repeatedly.
THE MACHINE HAS A VERY
Check the battery charge level (check the symbol on
LOW WORKING AUTONOMY
the control display).
The machine does not start.
THE MACHINE DOES
NOT MOVE
There is a drive pedal fault.
The quantity of detergent solution in the water system
is not sufficient for the work to be carried out.
NOT ENOUGH DETERGENT
SOLUTION ON THE BRUSH
Detergent solution filter obstructed.
The machine does not start.
Not enough detergent solution comes out.
The brushes have not been inserted correctly in
THE MACHINE DOES NOT
the machine.
CLEAN CORRECTLY
The type of brush used is not suitable for the dirt to
be removed.
The brush bristles are excessively worn.
The vacuum unit is obstructed.
THE SQUEEGEE DOES NOT
DRY PERFECTLY
The cap on the recovery tank drainage tube is not
properly positioned.
The recovery tank lid is not positioned correctly.
The detergent being used is not suitable.
EXCESSIVE FOAM
PRODUCTION
The floor is not very dirty.
The recovery tank is full.
THE MACHINE DOES NOT
VACUUM CORRECTLY
The vacuum device is obstructed
10077109-AB_UM_Maxima 2017 BT-BTO-BTS.indb 39
10077109-AB_UM_Maxima 2017 BT-BTO-BTS.indb 39
FIMAP spa
Fimap S.p.A.
Legal representative
Giancarlo Ruffo
TROUBLESHOOTING
POSSIBLE CAUSE
Make sure the main switch is on "I". If it isn't, turn the key clockwise.
Stop the machine immediately and contact the technician of the specialised service centre, or press the SOS
button if the HFM kit is installed.
Connect the batteries correctly inside the machine (see
If the battery charge level is critical, perform a complete recharge cycle (see paragraph
BATTERIES").
Reconnect the battery charger power cable.
Check that the battery charger power supply cable plug is connected to the mains socket.
Check that the characteristics in the battery charger plate are the same as those of the mains supply.
Referring to the battery charger use and maintenance manual, check the meaning of the flashing signals that the
battery charger emits dung the battery recharge stage.
If the battery charge level is critical, perform a complete recharge cycle (see
Read the section
Contact your nearest service centre.
Check that the amount of detergent solution present in the machine water system is sufficient for the work to be
carried out.
Check the detergent solution filter isn't obstructed. If it is, clean it (see
FILTER").
Read the section
Read the section
Check that the disc brushes have been correctly inserted in the machine (see
Make sure the brushes fitted on the machine are suitable for the work to be carried out (see
USING THE
Check the condition of the brush, and replace it if necessary (see
Make sure the squeegee is free of obstructions (see
Make sure the vacuum tube is free of obstructions (see
Make sure the vacuum cap filter is free of obstructions (see
Make sure the vacuum motor filter is free of obstructions (see
Check that the cap on the recovery tank drainage tube is positioned properly.
Check that the recovery tank lid is properly positioned on the machine.
Check that a low foam detergent has been used. If necessary, add a small quantity of anti foam liquid to the
recovery tank.
Dilute the detergent more.
Empty the recovery tank (see
Read the section
SOLUTION
"INSERTING THE BATTERIES IN THE
"THE MACHINE DOES NOT
START".
"THE MACHINE DOES NOT
START".
"NOT ENOUGH DETERGENT SOLUTION ON THE
BRUSHES".
"CLEANING THE SQUEEGEE
"CLEANING THE VACUUM
"EMPTYING THE RECOVERY
"THE SQUEEGEE DOES NOT DRY
PERFECTLY".
ENG - 39
MACHINE").
"CHARGING THE
"RECHARGING THE
BATTERIES").
"CLEANING THE WATER SYSTEM
BRUSH".
"ASSEMBLING THE
BRUSH").
"CHOOSING AND
"REPLACING THE BRUSH HEAD
BRUSH").
BODY").
TUBE").
"CLEANING THE RECOVERY
TANK").
"CLEANING THE RECOVERY
TANK").
TANK").
02/02/2024 10:27:35
02/02/2024 10:27:35
Publicidad
