Concept RM3000 Manual De Instrucciones página 30

EN
Grater
1. Place the work bowl on the body of the appliance and secure it by turning it
counter-clockwise (the arrows shown on the work bowl and the appliance body are
opposite each other when seated correctly).
2. Place the spindle extension on the coupling inside the work bowl.
3. Insert the required blade into the blade holder.
4. Place the blade holder on the spindle extension inside the work bowl.
5. Place the lid on the work bowl and secure it by turning it counter-clockwise (the
arrows shown on the lid and the handle of the work bowl are opposite each other
when seated correctly).
6. Insert the plug into the wall outlet.
7. Use the speed control to switch on the appliance at speed 1 or 2 (depending on the
type of food being prepared).
8. Place the food in the feed tube exclusively using the pusher.
9. After grating is completed, turn the speed control to the "0/OFF" position and
remove the plug from the wall outlet.
10. The bowl can now be removed.
Dicing blade set
1. Assemble the blade set (see figure).
2. Place the spindle extension on the coupling inside the work bowl.
3. Place the dicing blade set on the spindle extension inside the work bowl.
4. Part of the blade set with the grid must be placed at the level of the bowl handle.
5. Place the lid on the work bowl and secure it by turning it counter-clockwise (the
arrows shown on the lid and the handle of the work bowl are opposite each other
when seated correctly).
6. Place the work bowl on the body of the appliance and secure it by turning it
counter-clockwise (the arrows shown on the work bowl and the appliance body are
opposite each other when seated correctly).
7. Insert the plug into the wall outlet.
8. Use the speed control to switch on the appliance at speed 1 or 2 (depending on the
food being prepared).
9. Place the food in the feed tube exclusively using the pusher.
10. After dicing is completed, turn the speed control to the "0/OFF" position and
remove the plug from the wall outlet.
11. The bowl can now be removed.
58
Chopper/Kneading
1. Place the work bowl on the body of the appliance and secure it by turning it counter-
clockwise (the arrows shown on the work bowl and the appliance body are opposite
each other when seated correctly).
2. Place the chopping (kneading) blade on the coupling inside the work bowl.
3. Now put the ingredients in the bowl. Do not exceed the maximum permitted
amount of ingredients marked by the line on the work bowl.
4. Place the lid on the work bowl and secure it by turning it counter-clockwise (the
arrows shown on the lid and the handle of the work bowl are opposite each other
when seated correctly).
5. Insert the plug into the wall outlet.
6. Use the speed control to switch on the appliance at speed 1 or 2 (depending on the
food being prepared).
7. After chopping is completed, turn the speed control to the "0/OFF" position and
remove the plug from the wall outlet.
8. The bowl can now be removed.
Citrus juicer
1. Place the work bowl on the body of the appliance and secure it by turning it counter-
clockwise (the arrows shown on the work bowl and the appliance body are opposite
each other when seated correctly).
2. Place the spindle extension on the coupling inside the work bowl.
3. Place the juicer strainer on the spindle extension inside the work bowl and secure it
by turning it counter-clockwise (the lock mark on the juicer strainer is opposite the
handle of the work bowl when seated correctly).
4. Place the citrus cone on the juicer strainer.
5. Insert the plug into the wall outlet
6. Cut oranges or lemons in half. Place half of the citrus on the juicing cone and press
it lightly on the cone.
7. Use the speed control to switch on the appliance at speed 1 or 2 (depending on the
food being prepared).
8. After juicing is completed, turn the speed control to the "0/OFF" position and
remove the plug from the wall outlet.
Grinder
1. Fill the grinder container.
2. Place the blade part on the grinder container and secure it by turning it clockwise.
3. Turn the grinder downside down and place it on the appliance body and secure it by
turning it counter-clockwise.
4. Use the speed control to switch on the appliance at speed 1 or 2 (depending on the
food being prepared).
5. After grinding is completed, turn the speed control to the "0/OFF" position and
remove the plug from the wall outlet.
6. The coffee grinder can now be removed.
Note: Pulse operation can be used for all functions: Turn the speed control to "P"
position, the appliance operates at maximum power. When released, the speed control
returns to the "0/OFF" position.
RM3000 RM3000
EN
59