Descargar Imprimir esta página

Panasonic TX-48MZ800E Manual De Funcionamiento página 18

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 140
Analogue Channel Fine-tune: Select the channel you
want to adjust from the list and press OK. Then change
the frequency using the Left/Right directional buttons to
find optimal reception. Press the Back/Return button
to save and exit. When the confirmation dialogue ap-
pears, highlight OK and press OK to proceed.
Clear Channel List: Delete all channels stored in the
channel list. A dialogue will be displayed for confirma-
tion. Highlight Continue and press OK to proceed.
Highlight Cancel and press OK to cancel.
TV Options
Source: Display the list of input sources. Select the
desired one and press OK to switch to that source.
Picture: Open the Picture menu. Refer to the Display
& Sound section for detailed information.
Screen: Set the aspect ratio of the screen. Select one
of the predefined options according to your preference.
Sound: Open the Sound menu. Refer to the Display
& Sound section for detailed information.
Power: Check the Power & Energy menu options in
the Settings>System for additional power settings.
This menu has the same options as in the Power &
Energy>Power menu.
Sleep Timer: Define a time after which you want
your TV to enter sleep mode automatically. Set as
Off to disable.
Picture off: Select this option and press OK to
turn the screen off. Press a button on the remote
or on the TV to turn the screen on again. Note that
you can not turn the screen on via the Volume +/-,
Mute and Standby buttons. These buttons will
function normally.
Auto Sleep: Define an idle time after which you
want your TV to enter sleep mode automatically. 4
Hours, 6 Hours and 8 Hours options are available.
Set as Never to disable.
Parental Controls
(*) To enter this menu PIN should be entered first. Use the
PIN that you have defined during the initial setup process. If
you have changed the PIN after the initial setup use that PIN.
If you didn't set a PIN during the initial setup, you can use
the default PIN. The default PIN is 1234. Some options may
not be available or vary depending on the country selection
during the initial setup. The content of this menu may not
be displayed if the channel installation is not completed
and no channels are installed.
Channels Blocked: Select channel/s to be blocked
from the channel list. Highlight a channel and press
OK to select/unselect. To watch a blocked channel
PIN should be entered first.
Programme Restrictions: Block programmes
according to the age rating information that is being
broadcasted with them. You can turn on or off res-
trictions, set rating systems, age limits, and block
unrated programmes using the options of this menu.
Inputs Blocked: Prevent access to the selected
input source content. Highlight the desired input
option and press OK to select/unselect. To switch to
a blocked input source PIN should be entered first.
Change PIN: Change the PIN you defined during
the initial setup. Highlight this option and press OK.
You will need to enter the current PIN first. Then new
PIN entry screen will be displayed. Enter the new
PIN twice for confirmation.
CI Card: Display available menu options of the CI card
in use. This item may not be available depending on
the input source setting.
Advanced Options
The options of this menu may change and/or appear
as greyed out depending on the selected input source.
Audio
Audio Language: Set your language preference
for audio. This item may not be available
depending on the input source setting.
Second Audio Language: Set one of the listed
language options as second audio language
preference.
Soundtracks: Set your sound track preference,
if any available.
Audio Type: Set your audio type preference.
Visually Impaired: Set the Audio Type option
to Audio Description to enable this option.
Digital TV channels can broadcast special audio
commentary describing on-screen action, body
language, expressions and movements for people
with visual disabilities.
Speaker: Turn this option on if you want to hear
the audio commentary through the TV speakers.
Headphone: Turn this option on if you want to
route the sound of the audio commentary to the
TV's headphone output.
Volume: Adjust the volume level of the audio
commentary.
Pan and Fade: Turn this option on if you want to
hear the audio commentary more clearly, when
it is available through broadcast.
Audio for the Visually Impaired: Set your
audio preference for visually impaired. Options
will be available depending on the selected
broadcast.
Fader Control: Adjust the volume balance
between the main TV audio (Main) and audio
commentary (AD).
Subtitle
English - 17 -

Publicidad

loading