Publicidad
fire or a hot oven, or mechanically crush or cut the
battery, which may result in an explosion. Do not
leave the battery in an extremely high temperature
surrounding environment, which may result in an
explosion or the leakage of flammable liquid or gas.
Do not subject the battery to extremely low air
pressure, which may result in an explosion or the
leakage of flammable liquid or gas. + identifies the
positive terminal(s) of equipment which is used
with, or generates direct current. - identifies the
negative terminal(s) of equipment which is used
with, or generates direct current.
Fire Prevention
No naked flame sources, such as lighted candles,
should be placed on the equipment. The serial port
of the equipment is used for debugging only.
Hot Surface Prevention
For the device with sticker
pay attention to the following cautions:
CAUTION: Hot parts! Burned fingers when handling
the parts. Wait one-half hour after switching off
before handling parts. This sticker is to indicate that
the marked item can be hot and should not be
touched without taking care. For device with this
sticker, this device is intended for installation in a
restricted access location, access can only be gained
by service persons or by users who have been
instructed about the reasons for the restrictions
applied to the location and about any precautions
that shall be taken.
Installation
Install the device according to the instructions in
Quick Start Guide. To prevent injury, this device
must be securely attached to the installation
surface in accordance with the installation
instructions. Never place the device in an unstable
location. The device may fall, causing serious
personal injury or death. If the device needs to be
wired by yourself, select the corresponding wire to
supply power according to the electric parameters
labeled on the device. Strip off wire with a standard
wire stripper at corresponding position. To avoid
serious consequences, the length of stripped wire
shall be appropriate, and conductors shall not be
exposed. Make sure that the power has been
disconnected before you wire, install, or
disassemble the device.
Power Supply
Device powered by Safety Extra-Low Voltage(SELV):
The power source should meet limited power
source or PS2 requirements according to IEC
60950-1 or IEC 62368-1 standard.
Device powered by AC mains supply voltage: The
equipment must be connected to an earthed mains
socket-outlet. An appropriate readily accessible
disconnect device shall be incorporated external to
the equipment. An appropriate overcurrent
protective device shall be incorporated external to
the equipment, not exceeding the specification of
the building. An all-pole mains switch shall be
incorporated in the electrical installation of the
building. Ensure correct wiring of the terminals for
connection to an AC mains supply. The equipment
or
,
17
has been designed, when required, modified for
connection to an IT power distribution system.
If a power adapter is provided in the device package,
use the provided adapter only. If no power adapter
is provided, ensure the power adapter or other
power supply complies with Limited Power Source.
Refer to the product label for the power supply
output parameters.
White Light Illuminator (If supported)
Possibly hazardous optical radiation emitted from
this product. DO NOT stare at operating light source.
May be harmful to the eyes. Wear appropriate eye
protection or DO NOT turn on the white light when
you assemble, install or maintain the camera.
Transportation
Keep the device in original or similar packaging
while transporting it.
System Security
Please understand that you have the responsibility
to configure all the passwords and other security
settings about the device, and keep your user name
and password.
Maintenance
If the product does not work properly, please
contact your dealer or the nearest service center.
We shall not assume any responsibility for
problems caused by unauthorized repair or
maintenance. A few device components (e.g.,
electrolytic capacitor) require regular replacement.
The average lifespan varies, so periodic checking is
recommended. Contact your dealer for details.
Cleaning
Please use a soft and dry cloth when clean inside
and outside surfaces of the product cover. Do not
use alkaline detergents.
Using Environment
DO NOT place the camera in extremely hot, cold,
dusty or damp locations, and do not expose it to
high electromagnetic radiation.
Emergency
If smoke, odor, or noise arises from the device,
immediately turn off the power, unplug the power
cable, and contact the service center.
Time Synchronization
Set up device time manually for the first time access
if the local time is not synchronized with that of the
network. Visit the device via Web browse/client
software and go to time settings interface.
Reflection
Make sure that no reflective surface is too close to
the device lens. The IR light from the device may
reflect back into the lens causing reflection.
L'image du produit est donnée uniquement à
titre de référence et le produit réel peut
présenter un aspect différent.
Symboles et marques
i. Accessoire non forcément inclus.
ii. Nombre variable d'accessoires.
iii. Ignorez cette étape si elle n'est
Français
Publicidad
