Key Automation RAY2524 Instrucciones Y Advertencias Para Su Instalación Y Uso página 9

2 - PRODUCT OVERVIEW
2.1 - Description of the product
RAY gear motors are destined to be installed in systems for the
automation of gates with hinged doors.
RAY gear motors have been designed and constructed to be fitted
onto hinged doors within the weight limits indicated in the technical
2.2 - Model and technical characteristics
CODE
RAY2524
RAY4024E
RAY40
RAY40L
RAY2224
RAY4024R
RAY3024F
TECHNICAL DATA
Speed
Thrust force
Cycle/hour
Opening time at 90°
Working stroke
Control board
Power supply
Absorption
Engine power
Capacitor
Thermoprotection
Integrated lights
Degree of protection
Dimensions (L - P - H)
Weight
Operating temperature
Noise emission level
* with optimized fixing dimensions
** with non-panelled door at a temperature of 20°C
3 - PRELIMINARY CHECKS
Before installing this product, verify and check the following steps:
- Check that the gate or door are suitable for automation
- The weight and size of the gate or door must be within the
maximum permissible operating limits specified in Fig. 2
- Check the presence and strength of the security mechanical stops
of the gate or door
- Check that the mounting area of the product is not subject to
flooding
- Conditions of high acidity or salinity or proximity to heat sources
could cause malfunction of the product
- Extreme weather conditions (for example the presence of snow,
ice, high temperature range, high temperatures) may increase the
friction and therefore the force required for the handling and initial
DESCRIPTION
Gear motor for hinged doors with max length 3 m or max weight 500 kg, 24 Vdc
Gear motor for hinged doors with max length 4 m or max weight 600 kg with encoder, 24 Vdc
Gear motor for hinged doors with max length 4 m or max weight 600 kg, 230 Vac
Gear motor for hinged doors with max length 4 m or max weight 600 kg, 230 Vac, slow
Gear motor for hinged doors with max length 3 m or max weight 300 kg, 24 Vdc
Gear motor for hinged doors with max length 4 m or max weight 500 kg, 24 Vdc, reversible
Gear motor for hinged doors with max length 3 m or max weight 300 kg, 24 Vdc with encoder, fast
RAY4024
RAY2524
RAY4024E
2,6 cm/s 1,5 cm/s
1500 N 2000 N
40 40
18-25* 20-25*
14AB 14AB2
24 Vdc 24 Vdc 230 Vac 50/60 Hz 230 Vac 50/60 Hz
3,5 A 5 A
85 W 120 W
- -
- -
si si
6 kg 8 kg
specifications table.
The use of gear motors for applications which differ from those
indicated above is prohibited.
MODEL
RAY40 RAY40L
1,6 cm/s
1 cm/s
2000 N
1800 N
25
16
20-25*
32-40*
415 mm
CT202
CT202
1,2 A
1,3 A
280 W
300 W
8 µF 8 µF
150 °C 150 °C
-
-
IP44
844-100-104 mm
8 kg 8 kg
-20°+55°C
≤ 70dB(A)
starting point may be higher than under normal conditions.
- Check that the manual operation of gate or door is smooth and
friction-free and there is no risk of derailment of the same
- Check that the gate or door are in equilibrium and stationary if left
in any position
- Check that the power line to supply the product is equipped with
proper grounding safety and protected by a magnetothermal and
differential security device
- Provide the power system with a disconnecting device with a gap
of contacts enabling full disconnection under the conditions
dictated by the overvoltage category III.
- Ensure that all materials used for the installation comply with
current regulations
RAY2224 RAY4024R RAY3024F
2,6 cm/s 3 cm/s 3,8 cm/s
1500 N 1000 N 1000 N
40 40
18-25* 15-20*
CT20324 14AB2 14AB2F
24 Vdc 24 Vdc 24 Vdc
3,5 A 5 A
85 W 120 W 120 W
- -
- -
- si
6 kg 8 kg
EN
40
10-15*
5 A
-
-
si
8 kg
9