Johnson Controls 3G9080 Manual De Instrucciones

3G9080/3G9080-EU/3H9080/LE9080/LE9080-EU Cellular Alarm Communicator Installation Instructions
Safety information
All servicing, except backup battery replacement, must be performed by a service person only.
Use only authorized accessories with this equipment. Observe and respect all rules imposed by local electrical codes. This manual
contains information on limitations regarding product use and function, and on the limitations as to the liability of the manufacturer.
Read the entire manual carefully. For warning information, refer to the PowerSeries Pro alarm system Reference Manual. The
communicator must be installed by service persons only and used in an environment that provides a maximum pollution degree of 2 and
an overvoltages category II in non-hazardous, indoor locations only. Observe these instructions and the instructions specified within the
panel manual.
Technical specifications
The following technical specifications apply to all models.
Input voltage: 3.4 - 4.2 V, nominal 3.8 V (provided by the host alarm panels HS3032, HS3128, and HS3248).
Standby current: 12 - 28 mA at 3.8 V.
Alarm (transmitting) current:750 mA at 3.8 V (max avg).
Operating temperature: -10°C to 55°C. UL/ULC has only verified operation for range 0 °C to 49°C.
Relative humidity: 5% to 93%, noncondensing.
Mechanical specifications: 81 x 61 x 11 mm (W x L x H); weight is 25 g.
Model Market Operating frequency (MHz)
2G - B8: UL: 880 – 915, DL: 925 – 960
B3: UL: 1710 – 1785, DL: 1805 – 1880
3G - B1: UL: 1920 – 1980, DL: 2110 – 2170
B3: UL: 1710 – 1785, DL: 1805 – 1880
B8: UL: 880 - 915, DL: 925 - 960
LE9080-EU - CE compliant Europe 4G - B28A: UL: 703 – 733, DL: 758 – 788
B20: UL: 832 – 862, DL: 791 – 821
B8: UL: 880 – 915, DL: 925 – 960
B3: UL: 1710 – 1785, DL: 1805 – 1880
B1: UL 1920 - 1980, DL: 2110 - 2170
B7: UL: 2500 – 2570, DL: 2620 – 2690
3G - B5: UL: 824 – 849, DL: 869 – 894
B2: UL: 1850 – 1910, DL: 1930 – 1990
4G - B12: UL: 699 – 716, DL: 729 – 746
LE9080 - UL/ULC listed Canada, USA B13: UL: 777 – 787, DL: 746 – 756
B5: UL: 824 – 849, DL: 869 – 894
B4: UL: 1710 – 1755, DL: 2110 – 2170
B2: UL: 1850 – 1910, DL: 1930 – 1990
2G - B5: UL: 824 – 849, DL: 869 – 894
3G9080 - UL/ULC listed B2: UL: 1850 – 1910, DL: 1930 – 1990
Argentina
3G9080 - LAT 3G - B5: UL: 824 – 849, DL: 869 – 894
B2: UL: 1850 – 1910, DL: 1930 – 1990
2G - B8: UL: 880 – 915, DL: 925 – 960
B3: UL: 1710 – 1785, DL: 1805 – 1880
3G9080-EU - CE compliant Europe
3G - B8: UL: 880 – 915, DL: 925 – 960
B1: UL: 1920 – 1980, DL: 2110 – 2170
Inserting and removing the SIM card
CAUTION: Use caution when you handle the SIM card. To avoid damage to the SIM card, ensure that there are no bent or
scratched contacts.
To insert and remove the SIM card, complete the following step:
• I nsert or remove the SIM card by sliding it in or out of the holder. The notch on the corner of the SIM card must align with the notch on
the base of the holder.
Installing and replacing the communicator
Note: Before installing the communicator, confirm with the local service provider that there is an available and active network in
the area.
Opening the unit
To open the unit, complete the following step:
• D isconnect power from the panel by removing the power cord and battery.
Installing the communicator
To install the communicator, complete the following steps.
1. On the new communicator, if required, remove the protective metal tab from the 24-pin CON1 header.
2. Align the three holes on the communicator module with the plastic pegs on the alarm panel, ensuring the 24-pin connectors are
aligned with matching pins on the panel. See Figure 3.
3. Press the module carefully onto the alarm panel.
4. To attach the antenna place a nylon washer on either side of the hole on the panel and screw the cable into the antenna. See Figures 4
and 5.
5. Gently press the main antenna cable connector into the jack labeled JK2 – Main Ant on the PCB. Repeat this step for the diversity
antenna, and connect to the jack labeled JK1 – Div Ant on the PCB.
6. Apply power to the panel by plugging in the power supply module.
*29010165R005
29010165R005
Figure 1: Preparing the panel
Figure 3: Installing the communicator
Typical antenna gain (dBi)
1.9
3.2
2.2
3.2
1.9
1.0
2.3
1.9
3.2
2.2 Replacing the communicator
3.3
Note: For panels with a communicator installed, you can use the foam pad in the unit or the foam pad provided in the
1.3
standalone cellular communicator kit.
6.8
To replace the communicator, complete the following steps.
1.2
2.2 1. Disconnect power from the panel by unplugging the transformer and battery.
2. Gently remove the main and diversity antenna cables from the PCB.
1.3
3. Release the stand-offs and pull up on the communicator to remove it from the header.
4.6
6.8 4. Complete steps 1- 6 in Installing the Communicator.
Communicator configuration
1.4
For information on how to configure the communicator, refer to the PowerSeries Pro alarm system Reference Manual.
6.7
Placement test
1.4
6.7
To ensure that the communicator is active with a strong signal connection, place the PowerSeries Pro panel in its intended location and
perform the following steps.
2.0
4.6 1. Ensure the SIM card has been activated.
2. Using the keypad, enter placement test through installer's programming: [*][8][Installer Code][850].
2.0
6.7/2.8 3. View and record the number of bars showing on the LCD keypad.
4. Compare with the number of bars indicated in the CSQ Levels column shown in the following table.
5. If 3 or more bars are shown, the location is good and no further action is required.
6. If 2 or less bars are shown, the location is poor and the communicator may need to be relocated, or an external antenna extension kit
can be used to improve the signal strength.
Signal strength CSQ level
5 bars 14 and higher
4 bars 11 to 13
3 bars 7 to 10
2 bars 5 to 6
1 bar 1 to 4
No signal 0
Viewing troubles
For information on how to view troubles, refer to the PowerSeries Pro alarm system Reference Manual.
Limited warranty
Digital Security Controls (DSC) warrants that for a period of 12 months from the date of purchase, the product shall be free of defects
in materials and workmanship under normal use and that in fulfilment of any breach of such warranty, DSC shall, at its option, repair
or replace the defective equipment upon return of the equipment to its repair depot. This warranty applies only to defects in parts and
workmanship and not to damage incurred in shipping or handling, or damage due to causes beyond the control of Digital Security
Controls such as lightning, excessive voltage, mechanical shock, water damage, or damage arising out of abuse, alteration or improper
application of the equipment. The foregoing warranty shall apply only to the original buyer, and is and shall be in lieu of any and all other
warranties, whether expressed or implied and of all other obligations or liabilities on the part of Digital Security Controls. Digital Security
Figure 2: Preparing the communicator
Figure 4: One antenna installation Figure 5: Two antenna installation
Signal level (dBm) Installer action
-84 and higher
-90 to -85 Location is GOOD.
-98 to -91
-102 to -99
Location is BAD. Not suitable for
Cellular operation
-108 to -103
Check if Cellular coverage is active
-108.8
in your area.
Controls neither assumes responsibility for, nor authorizes any other person purporting to act on its behalf to modify or to change this
warranty, nor to assume for it any other warranty or liability concerning this product. In no event shall Digital Security Controls be liable
for any direct, indirect or consequential damages, loss of anticipated profits, loss of time or any other losses incurred by the buyer in
connection with the purchase, installation or operation or failure of this product. Warning: Digital Security Controls recommends that
the entire system be completely tested on a regular basis. However, despite frequent testing, and due to, but not limited to, criminal
tampering or electrical disruption, it is possible for this product to fail to perform as expected.
EULA
IMPORTANT - READ CAREFULLY: DSC Software purchased with or without Products and Components is copyrighted and is purchased
under the following license terms:
This End-User License Agreement ("EULA") is a legal agreement between You (the company, individual or entity who acquired
the Software and any related Hardware) and Digital Security Controls, a division of Tyco Safety Products Canada Ltd. ("DSC"),
the manufacturer of the integrated security systems and the developer of the software and any related products or components
("HARDWARE") which You acquired.
If the DSC software product ("SOFTWARE PRODUCT" or "SOFTWARE") is intended to be accompanied by HARDWARE, and is NOT
accompanied by new HARDWARE, You may not use, copy or install the SOFTWARE PRODUCT. The SOFTWARE PRODUCT includes
computer software, and may include associated media, printed materials, and "online" or electronic documentation.
Any software provided along with the SOFTWARE PRODUCT that is associated with a separate end-user license agreement is licensed to
You under the terms of that license agreement.
By installing, copying, downloading, storing, accessing or otherwise using the SOFTWARE PRODUCT, You agree unconditionally to be
bound by the terms of this EULA, even if this EULA is deemed to be a modification of any previous arrangement or contract. If You do not
agree to the terms of this EULA, DSC is unwilling to license the SOFTWARE PRODUCT to You, and You have no right to use it.
SOFTWARE PRODUCT LICENSE
The SOFTWARE PRODUCT is protected by copyright laws and international copyright treaties, as well as other intellectual property laws
and treaties. The SOFTWARE PRODUCT is licensed, not sold.
1. GRANT OF LICENSE This EULA grants You the following rights:
Software Installation and Use - For each license You acquire, You may have only one copy of the SOFTWARE PRODUCT installed.
Storage/Network Use - The SOFTWARE PRODUCT may not be installed, accessed, displayed, run, shared or used concurrently on or from
different computers, including a workstation, terminal or other digital electronic device ("Device"). In other words, if You have several
workstations, You will have to acquire a license for each workstation where the SOFTWARE will be used.
Backup Copy - You may make back-up copies of the SOFTWARE PRODUCT, but You may only have one copy per license installed at any
given time. You may use the back-up copy solely for archival purposes. Except as expressly provided in this EULA, You may not otherwise
make copies of the SOFTWARE PRODUCT, including the printed materials accompanying the SOFTWARE.
1. DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS
Limitations on Reverse Engineering, Decompilation and Disassembly - You may not reverse engineer, decompile, or disassemble
the SOFTWARE PRODUCT, except and only to the extent that such activity is expressly permitted by applicable law notwithstanding this
limitation. You may not make any changes or modifications to the Software, without the written permission of an officer of DSC. You
may not remove any proprietary notices, marks or labels from the Software Product. You shall institute reasonable measures to ensure
compliance with the terms and conditions of this EULA.
Separation of Components - The SOFTWARE PRODUCT is licensed as a single product. Its component parts may not be separated for
use on more than one HARDWARE unit.
Single INTEGRATED PRODUCT - If You acquired this SOFTWARE with HARDWARE, then the SOFTWARE PRODUCT is licensed with the
HARDWARE as a single integrated product. In this case, the SOFTWARE PRODUCT may only be used with the HARDWARE as set forth in
this EULA.
Rental - You may not rent, lease or lend the SOFTWARE PRODUCT. You may not make it available to others or post it on a server or web
site.
Software Product Transfer - You may transfer all of Your rights under this EULA only as part of a permanent sale or transfer of the
HARDWARE, provided You retain no copies, You transfer all of the SOFTWARE PRODUCT (including all component parts, the media and
printed materials, any upgrades and this EULA), and provided the recipient agrees to the terms of this EULA. If the SOFTWARE PRODUCT
is an upgrade, any transfer must also include all prior versions of the SOFTWARE PRODUCT.
Termination - Without prejudice to any other rights, DSC may terminate this EULA if You fail to comply with the terms and conditions of
this EULA. In such event, You must destroy all copies of the SOFTWARE PRODUCT and all of its component parts.
Trademarks - This EULA does not grant You any rights in connection with any trademarks or service marks of DSC or its suppliers.
1. COPYRIGHT
All title and intellectual property rights in and to the SOFTWARE PRODUCT (including but not limited to any images, photographs, and text
incorporated into the SOFTWARE PRODUCT), the accompanying printed materials, and any copies of the SOFTWARE PRODUCT, are owned
by DSC or its suppliers. You may not copy the printed materials accompanying the SOFTWARE PRODUCT. All title and intellectual property
rights in and to the content which may be accessed through use of the SOFTWARE PRODUCT are the property of the respective content
owner and may be protected by applicable copyright or other intellectual property laws and treaties. This EULA grants You no rights to
use such content. All rights not expressly granted under this EULA are reserved by DSC and its suppliers.
EXPORT RESTRICTIONS - You agree that You will not export or re-export the SOFTWARE PRODUCT to any country, person, or entity subject
to Canadian export restrictions.
CHOICE OF LAW - This Software License Agreement is governed by the laws of the Province of Ontario, Canada.
ARBITRATION - All disputes arising in connection with this Agreement shall be determined by final and binding arbitration in accordance
with the Arbitration Act, and the parties agree to be bound by the arbitrator's decision. The place of arbitration shall be Toronto, Canada,
and the language of the arbitration shall be English.