Publicidad
Idiomas disponibles
Idiomas disponibles
Lubrication
The motor is equipped
with bearings
that contain sufficient lubrication for the
life of the motor, The addition of lubricant
could cause damage. Therefore,
do not
add lubricant to motor
bearings.
The agitator is equipped with two ball
bearings that should be lubricated
periodically
by a Hoover Factory
Service Center or an Authorized
Hoover
Warranty Service Dealer (Depot).
Therma|
protector
An internal thermal protector has been
designed
into your cleaner to protect it
from overheating.
When the thermal
protector
activates,
the cleaner will stop running
If this
happens, proceed as follows:
1. Turn the cleaner OFF and discon-
nect it from the electrical outlet.
2. Check dirt cup pre-filter, HEPA
cartridge filter and secondary and final
filters for dirt accumulation.
3. Refer to "Clearing blockages"
section.
4. When cleaner is unplugged
and
the motor cools for 30 minutes,
the
thermal protector automatically
resets
and cleaning may continue.
If the thermal protector continues to
activate after following the above steps,
your cleaner may need servicing (see
"Service" section).
Service
To obtain approved
HOOVER service
and genuine HOOVER parts, locate
the nearest Hoover Factory Service
Center or Authorized
Hoover
Warranty
Service Dealer (Depot) by:
,checking the Yellow Pages under
"Vacuum Cleaners - Household" OR -
, checking
the list of Factory Service
Centers provided with this cleaner
OR-
, calling 1-800-944-9200
for an
automated referral of authorized
service outlet locations (U.S. only)
OR-
, checking
the Service section of The
Hoover Company on-line at
www.hoover,
com
Do not send your cleaner to The Hoover
Company in North Canton for service,
this will only result in delay.
If further assistance is needed, contact
The Hoover Company Consumer
Response Center, North Canton,
Ohio 44720, Phone: 330-499-9499.
In Canada, contact Hoover Canada,
Burlington, Ontario L7R 4A8,
Phone:
1-800-263-6376.
Always identify your cleaner by the
complete
model number when
requesting
information or ordering parts.
(The model number appears on the bot-
tom of the cleaner.)
Hoover
Cleaning
Performance
This Hoover Cleaning Performance Sys-
tem is for comparing
the relative pro-
gressive performance
of Hoover
uprights
only and not for comparison
with any other brands. The majority of
this rating is based upon the American
Society for Testing and Materials (ASTM)
Carpet Cleaning Effectiveness
Test
(ASTM Test F608). Other performance
factors include Hose Power (ASTM Test
F558), Surface Litter Cleaning, Hard
Floor Cleaning, Edge Cleaning, Cleaning
Width, and Air Filtration.
If a minor problem occurs, it usually can
be solved quite easily when the cause is
found by using the check list below.
Possible cause
Possible solution
• Not firmly plugged
in
• Plug unit in firmly
• No voltage
in wall plug
• Check fuse or breaker
• Blown fuse or tripped
breaker
• Replace fuse or reset breaker
• Thermal protector
activated
• Allow cleaner to cool for 30 minutes
(this will reset the thermal protector) (see
pg. 13).
Possible cause
Possible solution
• Broken or worn belt
• Replace belt
• Agitator brush roll worn
• Replace brush roll
• Dirt cup full
• Empty dirt cup
• Incorrect
carpet height setting
• Move nozzle control knob to lower
setting
• Blockage in air flow passage
• Clear blockage
• HEPA cartridge filter clogged
• Clean HEPA cartridge filter by either
tapping the side of the dirt cup or
removing the cartridge
filter as de-
scribed in the "Filter assembly"
section.
• Pre-filter clogged
• Clean pre-filter as described in
"Filter assembly"
section.
Dirt cup not properly installed
and
latched
Position dirt cup properly and lock
latch (Fig. 3-4).
Dirt cup lid not positioned
properly
or missing
Ensure that dirt cup lid is properly
positioned.
Filter assembly
not assembled
properly
Ensure that filter assembly is
positioned properly (Figs. 3-8 to 3-10).
Possible cause
Possible solution
• Incorrect
carpet height setting
• Move nozzle control knob to a
higher setting
=
eo
*
".
.
®0
•
o
Possible cause
Possible solution
• Cleaner handle not in upright
position
• Ensure that cleaner handle is locked in
upright position.
• Blockage in hose
• Clear blockage.
Possible cause
Possible solution
• Filter assembly
not installed
properly
• Remove filter assembly from dirt cup
and ensure that HEPA cartridge filter is
properly attached to pre-filter screen
and that entire filter assembly is
properly repositioned
inside dirt cup.
(Figs. 3-5 through 3-10).
Note: Heavy debris may settle to the
bottom of the dirt cup and prevent the
dirt from spinning without affecting
cleaning performance.
The cleaner can
continue to be used even if the dirt is not
spinning inside the dirt cup.
However, if the dirt does stop spinning
AND there is a noticeable
decrease of
performance,
check the items under
"Cleaner won't pick up".
Possible cause
Possible solution
• Too much pressure
being applied
to
tool
• Continue using tool applying light
pressure.
• Blockage in turbine
channel
• Remove blockage.
Continued
-_
13
Publicidad
