Mennekes AMTRON 4You 300 Guía Rápida Para El Operador página 3

EN
Safety
• Only a qualified electrician may open and work on the product – Danger to life due to electric shock
• Do not use a damaged product – Danger to life due to electric shock
Check the product for operational readiness and external damage daily and/or prior to each charging process.
• Do not use adapter plugs or extension cables – Danger to life due to electric shock
• Avoid activities / situations (Fig. 1 on the cover page) – Material damage
LED status display
Managing RFID cards (teach mode)
The supplied RFID cards are already taught in
the local whitelist.
⊲ Hold the master RFID card in front of the card reader (C) to
activate teach mode for 1 minute.
→ B flashes blue quickly, and a signal sounds for 2 seconds.
Adding a user RFID card to the whitelist:
⊲ Hold the new user RFID card in front of the card reader.
→ B flashes green for 1 second, and an ascending sequence of
notes sounds.
The whitelist is full (max. 10 RFID cards):
→ A flashes red for 3 seconds, and a signal sounds for
2 seconds.
Removing a user RFID card from the whitelist:
⊲ Hold the known user RFID card in front of the card reader.
→ A flashes red for 1 second, and a descending sequence of
notes sounds.
Removing all user RFID cards from the whitelist:
⊲ Hold the master RFID card in front of the card reader for
10 seconds.
→ A flashes red for 1 second, and a descending sequence of
notes sounds.
Charging modes
"Fast charging"
Provided the wallbox has been correctly connected and configured for the "Solar charging" and / or "Solar-assisted charging"
charging modes by the qualified electrician, the additional charging modes will be available (press the buttons to set the charging
mode):
"Solar charging"
"Solar-assisted charging"
Download and read the complete manual:
AMTRON® 4You 300 7,4
https://mennek.es/products/?part_no
=1313207205&source=manual&fl=en
A & B are off: Energy-saving mode active. An interaction with the wallbox (e.g. authorisation)
will end energy-saving mode. A qualified electrician can configure the energy-saving mode,
A
which is enabled in the delivery state.
Colour blue (default colour setting):
• A & B light up: Standby.
• A & B flash: Authorisation is taking place (valid for 5 minutes). No vehicle connected.
• B flashes: Vehicle connected. Missing authorisation.
• A & B pulsate: Charging paused. Not all requirements for charging are met (Requirements:
see complete manual).
Colour green (default colour setting):
• A & B light up: Charging in progress.
B
• A & B pulsate: Charging paused (feedback from vehicle).
Colour red:
• A lights up: Fault – qualified electrician required.
• A flashes: Fault – end charging process and restart. Some faults are rectified automatically
if you wait a bit. A qualified electrician is needed if the fault persists / recurs.
Charging at maximum charging power.
The charging power is dependent on the excess energy from the photovoltaic system. Charging
exclusively with solar energy.
The charging power is dependent on the excess energy from the photovoltaic system. Charging
with minimum charging power is always possible (with grid power, if necessary).
Starting the charging process
C ⊲ Connect the charging cable to the vehicle.
⊲ If necessary, hold the taught user RFID card in front of the
card reader (C).
Ending the charging process
⊲ End the charging process on the vehicle or by holding the
user RFID card in front of the card reader.
⊲ Grasp the charging cable at the charging plug, and pull it out of
the charging socket.
⊲ Put the protective cap on the charging plug.
⊲ Hang the charging cable on the housing without any kinks.
Detach front cover – see Fig. 2 on cover page.
Attach front cover – see Fig. 3 on cover page.
AMTRON® 4You 300 11 /
AMTRON® 4You 300 22
https://mennek.es/products/?part_no
=1313202205&source=manual&fl=en
3