Worx WG829E Manual página 12

Assembling the Pump
Install the pump into the tank and rotate
clockwise to tighten.
Assembling the Shoulder Strap
Starting
Press the power button to turn on the
sprayer, the LED light will be green and an
audible hum will be heard, which means
the machine is working. And it will stop
once the tank is pressurized, which may
take 30 seconds to several minutes
depending on the size of the tank and the
amount of liquid inside.
NOTE: The greater amount of liquid in the
tank, the less time it takes to pressurize.
NOTE: Once the sprayer is used and
releases a certain amount of liquid, the
pump will kick back on to maintain a
steady stream.
Spraying
Aim the wand in the desired direction and
depress the lever to spray. Release the
lever to stop.
For continuous spraying, please depress
the lever and lock it in the depressed
position.
NOTE: When the battery power is low, the
LED light will flash green.After usage, turn
off the sprayer, then remove any chemical
12
and clean the machine.
Adjustable Sprayer Nozzle
The adjustable spray nozzle offers
variable spray patterns:
Loosen nozzle for a long, thin stream,
tighten for a wider mist.
NOTE: Do not loosen the nozzle nut
overly, which may result in the water leak.
AFTER OPERATION
After each usage, press the power
button to turn off the machine. You
must first pull up the pressure release
valve to release the pressure inside of
the tank. Then rotate the pump handle
counterclockwise to remove the pump.
Storage
When not in use, store the wand as Fig. I
shown.
MAINTENANCE
Before any maintenance, please depressurize the
sprayer by turn off the machine and pull of the pressure
release valve until all air pressure is released.
Pump maintenance
Inspect the pump frequently whether any leaking occurs
20V Yard Sprayer
around the pump seal. If leaking occurs, please contact
service center.
See Fig. D
Nozzle maintenance
Clean the openings of any obstructions or residue. Do not
See Fig. E
use sharp tools that could scratch or damage the nozzle.
Hose maintenance
Clean the filter at the end of the hose regularly for a
better performance. (See Fig. J)
Shut-off maintenance
Remove the filter from the shut-off assembly. Clean the
See Fig. F1
debris inside and clean the filter by rinsing with cool,
clean water. (See Fig. K)
Replace the O- ring and rubber plug. (See Fig. L1, L2)
WARNING: Contact the solutions center before
attempting any other servicing.
CLEANING AND STORAGE
Empty any extra chemical from the tank. Use clean
water to thoroughly rinse the tank until all chemical
and residues are removed. Use a wet cloth to wipe the
bottom of the pump until all chemical and residues are
See Fig.
removed. Do not rinse the pump with a hose or submerge
F2, F3
in water, as water will enter the housing resulting in the
pump non-functional. With clean water in the clean tank,
spray water through the hose, shut-off lever, wand, and
nozzle for at least 30 seconds to rinse the chemical
out. Remove the pump. Do not put the pump down as
it may cause the pump is contaminated with dirt, grass
clippings, or debris that will enter the tank later. Hanging
the tank upside down to let the sprayer drain. Once the
sprayer is dried, please turn the sprayer upright and
See Fig. G1,
loosely attach the pump to the tank to prevent debris
G2
from entering the tank. Store the machine in a warm, dry
place out of direct sunlight.
FOR BATTERY TOOLS
The ambient temperature range for the use and storage
of tool and battery is 0
See Fig. H1,
The recommended ambient temperature range for
H2
the charging system during charging is 0
(32°F-104°F).
ENVIRONMENTAL
See Fig. I
PROTECTION
Waste electrical products must not be disposed
of with household waste. Please recycle where
facilities exist. Check with your local authorities or
retailer for recycling advice.
C-45 C (32°F-113°F).
o o
C-40 C
o o
EN