Publicidad
Idiomas disponibles
Idiomas disponibles
EN
(1). Use the provided spirit level (4) to ensure
the wall plate (1) is level.
3. Pre-drill the holes to a minimum depth of 55mm
using a 4.5mm drill bit. If installing in hard-
wood, a slightly larger diameter and deeper
hole may be required.
4. Place the washers (W-C) onto the lag bolts (W-
A). Attach the wall plate (1) to the wall using the
lag bolts (W-A).
Option B: Installing in masonry (Figure E)
Ensure there is a minimum of 35mm of
actual concrete/brick thickness in the
location of each hole.
Drill into solid concrete/bricks only. Do not
drill into mortar joints.
1. Mark a minimum of four mounting holes using
the wall plate (1) as a guide. Position two holes
at either end of the wall plate (1). Use the provi-
ded spirit level (4) to ensure the wall plate (1) is
level.
2. Drill the holes to a minimum depth of 60mm
using a 10mm masonry drill bit. Clean out the
holes after drilling.
3. Fully insert a concrete anchor (W-B) into each
hole. Tap the anchor in using a hammer if requi-
red.
4. Place the washers (W-C) onto the lag bolts (W-
A). Attach the wall plate (1) to the wall using the
lag bolts (W-A).
Attach Mounting Arms to TV (Figure F)
1. Using a second person for assistance, lay your
TV face down on something soft so as not to
scratch the TV screen. Check the back of your
TV to find the appropriate mounting pattern.
Do not place the TV face down onto a table
smaller than the TV itself, as doing so may
crack or damage the TV screen.
2. Sort through the provided bolts (M-A, M-B, M-C)
until you find the correct size that fits into the
mounting holes on the back of your TV. Test if
6
the bolts can be tightened by hand for at least
three full turns. Do not yet fully tighten the
bolts.
If you feel resistance while turning the bolt
you must stop immediately and select a
shorter bolt. Forcing in an oversized bolt
may cause damage to your TV (see figure G)
3. Remove the bolts from the TV once you have
selected the correct bolt size.
Refer to your local hardware supplier for the
correct bolts and washers if none of the
supplied bolts will fit your TV.
4. Gently place the mounting arms (2) on the back
of the TV. If the back of your TV is curved or re-
cessed you may need to use one or more of the
supplied spacers (M-E or M-F). When using a
spacer you may also need to use a longer bolt.
Keep in mind that the bolt must always be able
to turn at least three full turns (see figure G).
5. Place the washers (M-D) onto the previously
selected bolts. Attach the mounting arms (2) to
the TV using the bolts. Do not over tighten the
bolts, as doing so may cause damage to your
TV.
Attach TV to wall (Figure H)
1. Using a second person for assistance, carefully
lift the TV and hook the arms (2) over the top
of the wall plate (1). Note that there are three
height options on the mounting arms (2 to
choose from.
2. Gently pull down on the unlocking cords (3) on
the mounting arms (2) to open the locks into
the ready position.
3. Slowly lower the bottom of the TV until the bot-
tom of the mounting arm (2) locks into the bot-
tom of the wall plate (1). Release the unlocking
cords (3) to secure the TV onto the wall plate (1).
4. To remove the TV from the wall plate, gently pull
the unlocking cords (3) to release the mounting
arms (2). Using a second person for assistance,
pull the bottom of the TV slightly forwards and
then lift the TV up from the wall plate (1).
WWW.VONROC.COM
Publicidad
