AL-KO COMBI-CARE 36 E comfort Traducción Del Manual Original De Instrucciones página 20

GB
6 OPERATION
NOTE Always mow the grass before scari-
fying (max. grass height: 4 cm). Remove any for-
eign bodies from the grass surface.
6.1 Folding the handlebar in and out (05)
CAUTION! Danger of crushing. Fingers or
other parts of the body can be crushed between
the loose parts of the handlebar.
■
Hold the loose parts of the handlebar tightly.
■
Do not hold any fingers or other parts of the
body between the loose parts.
IMPORTANT! Danger of damaging the pow-
er cable. The motor and mains cables can be
crushed and damaged between the loose parts of
the handlebar.
■
Do not jam the cables when folding the han-
dlebar in/out.
Folding in the handlebar
1. Release the quick release on the rotary/snap-
in joints (05/1) until the entire handlebar
(05/2) can be folded forward into the horizon-
tal position (pos. a).
2. Release the bottom quick release (05/3) and
fold the top handlebar incl. middle part (05/4)
to the rear (pos. b).
3. Release the top quick release (05/5) and fold
the handlebar (05/6) forward into the horizon-
tal position (pos. c).
4. Slightly tighten all quick releases.
Folding out the handlebar
Proceed in reverse order.
6.2 Adjusting the handlebar to the body
size (06)
1. Loosen the quick release on the rotary/snap-
in joints (06/1).
2. Turn the handlebar to the desired height
(pos. a) at the handle (06/2). The rotary
movement is limited by the end stops (06/3)
of the rotary/snap-in joint.
3. Tighten the quick releases (06/1).
6.3 Setting the working depth (07)
The setting of the working depth depends on:
■
Grass condition (well-kept: low working
depth, overgrown: large working depth)
■
Blade wear (new: low working depth, worn:
large working depth)
20
If the working depth is too large: The appliance
stands still and the motor does not run.
IMPORTANT! Danger of damage to the
appliance. Setting the working depth with the ap-
pliance running causes damage.
■
Only set the working depth when the motor
and blade system have stopped.
1. Turn the adjuster wheel (07/1) to HIGH, i.e.
level 1 on the working depth indicator (07/2).
The blade system is raised to the maximum.
2. Checking the working depth:
■
Start the appliance (see chapter 6.5
"Starting and stopping the motor (09)",
page 20).
■
Move a little way onto the grass and
check the result. If the grass is too short
or irregularly scarified, the blade system
must be lowered.
3. Stop the appliance and wait until the blade
system has stopped.
4. Turn the adjuster wheel (07/1) a little towards
LOW, i.e. levels 2 to 5. The blade system is
lowered.
5. Repeat the previous steps until the grass is
uniformly scarified.
6.4 Establishing the mains connection (08)
1. Firmly plug the socket (08/1) of the mains ca-
ble into the plug (08/2) on the motor switch.
2. Clamp the mains cable (08/3) in the cable
strain relief (08/4) (pos. a, pos. b) so it cannot
be pulled off the motor switch.
6.5 Starting and stopping the motor (09)
IMPORTANT! Danger of damage to the ap-
pliance. The motor and blade system can be
damaged by consecutively switching on and off
briefly several times.
■
Only switch the motor on when the blade sys-
tem has stopped.
Starting the motor
1. Press and hold the safety push switch (09/1)
(pos. a).
2. Pull the motor switch bracket (09/2) to the
handlebar (09/3) (pos. b). The motor and
blade system are started.
3. Release the safety push switch (09/1) and
hold the motor switch bracket (09/2).
Operation
COMBI-CARE 36 E comfort