Publicidad
Idiomas disponibles
Idiomas disponibles
OPERATION
OPERATION
IMPORTANT: Always follow safety precautions when operating this equip-
ment. Review the safety instructions.
IMPORTANT: Always follow safety precautions when operating this equip-
ment. Review the safety instructions.
not operate the system in the presence of any source of ignition including running or
hot engines, lighted tobacco products, gas or electric heaters, or any type of electronic
not operate the system in the presence of any source of ignition including running or
device. A spark can ignite fuel vapors.
hot engines, lighted tobacco products, gas or electric heaters, or any type of electronic
device. A spark can ignite fuel vapors.
tight. If damaged, replace hoses before use.
OPERATION
tight. If damaged, replace hoses before use.
NOTE: Make sure the work area is dry.
IMPORTANT: Always follow safety precautions when operating this equip-
Dispense Fuel
NOTE: Make sure the work area is dry.
ment. Review the safety instructions.
1.
Insert suction hose.
NOTE: Ensure the tank contains enough fuel.
2.
Insert the nozzle into the receiving tank.
NOTE: Ensure the tank contains enough fuel.
IMPORTANT: Make sure the fuel is not contaminated with debris. Tighten loose tank
not operate the system in the presence of any source of ignition including running or
3.
Turn on the pump with the inline switch (see Figure 4).
lids regularly.
hot engines, lighted tobacco products, gas or electric heaters, or any type of electronic
IMPORTANT: Make sure the fuel is not contaminated with debris. Tighten loose tank
4.
Squeeze the nozzle handle to start fuel flow.
device. A spark can ignite fuel vapors.
lids regularly.
5.
When done, release the nozzle handle and turn the pump off at the switch.
do not run the pump more than 10 minutes with the nozzle closed. Leaving the pump
NOTE: Always insert nozzle into tank before turning pump on.
on with the nozzle closed for more than 10 minutes can damage the pump components
tight. If damaged, replace hoses before use.
do not run the pump more than 10 minutes with the nozzle closed. Leaving the pump
NOTE: This pump is designed to be self-priming. If fuel is not delivered within
and will void the warranty.
on with the nozzle closed for more than 10 minutes can damage the pump components
NOTE: Make sure the work area is dry.
15 to 20 seconds, turn the pump off and scan the QR code on page 10 for
and will void the warranty.
troubleshooting information.
NOTE: When finished refueling, make sure the pump is turned off at the switch
IMPORTANT: This is an intermittent duty pump, after running the pump for a
and disconnect the power cord from the 12-volt power source.
NOTE: Ensure the tank contains enough fuel.
maximum of 30 minutes, allow it to cool for 30 minutes.
IMPORTANT: This is an intermittent duty pump, after running the pump for a
IMPORTANT: Make sure the fuel is not contaminated with debris. Tighten loose tank
maximum of 30 minutes, allow it to cool for 30 minutes.
IMPORTANT: The motor is provided with an internal temperature-limiting device.
lids regularly.
Excessive motor heat will trip the device and will only reset after the motor has cooled.
IMPORTANT: The motor is provided with an internal temperature-limiting device.
If the device trips, turn the switch OFF and let the pump cool for 30 min. Turn the
Excessive motor heat will trip the device and will only reset after the motor has cooled.
switch ON again when ready to operate. If the device trips again before the end of the
If the device trips, turn the switch OFF and let the pump cool for 30 min. Turn the
do not run the pump more than 10 minutes with the nozzle closed. Leaving the pump
duty cycle, see the troubleshooting guide.
switch ON again when ready to operate. If the device trips again before the end of the
on with the nozzle closed for more than 10 minutes can damage the pump components
duty cycle, see the troubleshooting guide.
and will void the warranty.
start pumping.
start pumping.
IMPORTANT: This is an intermittent duty pump, after running the pump for a
IMPORTANT: This is an intermittent duty pump, after running the pump for a
maximum of 15 minutes, allow it to cool for 30 minutes.
IMPORTANT: This is an intermittent duty pump, after running the pump for a
maximum of 30 minutes, allow it to cool for 30 minutes.
maximum of 15 minutes, allow it to cool for 30 minutes.
IMPORTANT: The motor is provided with an internal auxiliary timer circuit that limits
IMPORTANT: The motor is provided with an internal temperature-limiting device.
operation of the pump to the listed duty cycle. The timer circuit will turn th epump off
IMPORTANT: The motor is provided with an internal auxiliary timer circuit that limits
Excessive motor heat will trip the device and will only reset after the motor has cooled.
whn duty cycle is exceeded. After allowing the pump to cool for 30 minutes the pump
operation of the pump to the listed duty cycle. The timer circuit will turn th epump off
If the device trips, turn the switch OFF and let the pump cool for 30 min. Turn the
can be reset by turning the switch off and on.
whn duty cycle is exceeded. After allowing the pump to cool for 30 minutes the pump
switch ON again when ready to operate. If the device trips again before the end of the
can be reset by turning the switch off and on.
duty cycle, see the troubleshooting guide.
start pumping.
IMPORTANT: This is an intermittent duty pump, after running the pump for a
maximum of 15 minutes, allow it to cool for 30 minutes.
IMPORTANT: The motor is provided with an internal auxiliary timer circuit that limits
operation of the pump to the listed duty cycle. The timer circuit will turn th epump off
whn duty cycle is exceeded. After allowing the pump to cool for 30 minutes the pump
can be reset by turning the switch off and on.
Fuse & Holder
EN
To prevent physical injury or property damage, observe
precautions against fire or explosion when dispensing fuel. Do
To prevent physical injury or property damage, observe
precautions against fire or explosion when dispensing fuel. Do
Before each use, repair leaks around seals or connections.
Make sure hoses are in good condition and connections are
Before each use, repair leaks around seals or connections.
Make sure hoses are in good condition and connections are
Make sure the pump is properly grounded. Repair any corroded
or damaged wiring before use.
Make sure the pump is properly grounded. Repair any corroded
To prevent physical injury or property damage, observe
or damaged wiring before use.
precautions against fire or explosion when dispensing fuel. Do
An automatic bypass valve prevents pressure build up when
the pump is on with the nozzle closed. To avoid pump damage,
Before each use, repair leaks around seals or connections.
An automatic bypass valve prevents pressure build up when
Make sure hoses are in good condition and connections are
the pump is on with the nozzle closed. To avoid pump damage,
Never leave the pump running without fluid. Dry running can
Make sure the pump is properly grounded. Repair any corroded
damage the pump components, and will void the warranty.
Never leave the pump running without fluid. Dry running can
or damaged wiring before use.
damage the pump components, and will void the warranty.
An automatic bypass valve prevents pressure build up when
the pump is on with the nozzle closed. To avoid pump damage,
Always turn the pump off if the temperature-limiting device
trips. If left on, the pump will automatically reset when cool and
Always turn the pump off if the temperature-limiting device
Never leave the pump running without fluid. Dry running can
trips. If left on, the pump will automatically reset when cool and
damage the pump components, and will void the warranty.
Always turn the pump off if the temperature-limiting device
trips. If left on, the pump will automatically reset when cool and
Switch
Figure 4
1
1
2
2
3
3
1
4
4
2
5
5
6
3
6
7
4
7
8
8
5
9
9
6
10
10
7
11
11
8
12
12
9
10
11
12
9
Publicidad
