Publicidad
Idiomas disponibles
Idiomas disponibles
English
Fitting the side handle (Fig. B)
• Turn the knob
counterclockwise until you can slide the
7C
side handle
7
onto the front of the tool as shown.
• Rotate the side handle into the desired position ensuring that
the notches
7A
engage with the sprocket
• Tighten the side handle by turning the knob
nOTE: The side handle can be positioned, depending on
personal preference.
Fitting an accessory (Fig. C)
• Press the chuck lock
6
.
• Open the chuck
by turning the sleeve counterclockwise.
5
• Insert the bit shaft
8
into the chuck.
• Tighten the chuck by turning the sleeve clockwise.
USE
WARNING! Let the tool work at its own pace. Do
not overload.
WARNING! Before drilling into walls, floors or ceilings, check
for the location of wiring and pipes.
Switching on and off (Fig. D, G)
• To switch the tool on, press the variable speed switch
tool speed depends on how far you press the switch.
• For continuous operation, press the lock-on button
release the variable speed switch.
This option does not work in reverse rotation.
• To switch the tool off, release the variable speed switch.
To switch the tool off when in continuous operation, press the
variable speed switch once more and release it.
Always hold the tool as shown in Figures D and G.
Selecting the direction of rotation (Fig. E)
For drilling and tightening screws, use forward (clockwise)
rotation. For loosening screws or removing a jammed drill bit,
use reverse (counterclockwise) rotation.
• To select forward rotation, push the forward/reverse slider
to the left.
• To select reverse rotation, push the forward/reverse slider to
the right.
WARNING! Never change the direction of rotation while the
motor is running.
Selecting the drilling mode (Fig. F)
q
For impact drilling in masonry and concrete, set the drilling
mode selector
4
to the
For drilling in steel, wood and plastics or for screwdriving set the
operating mode selector
4
Accessories
The performance of your tool depends on the accessory used.
BLACK+DECKER accessories are engineered to high quality
standards and designed to enhance the performance of your
tool. By using these accessories you will get the very best from
your tool.
MAINTENANCE
Your BLACK+DECKER corded/cordless appliance/tool has been
designed to operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation depends
upon proper tool care and regular cleaning.
WARNING! Before performing any maintenance on corded/
cordless power tools:
6
7B
.
clockwise.
7C
position.
r
to the
position.
• Switch off and unplug the appliance/tool.
• Or switch off and remove the battery from the appliance/tool
if the appliance/tool has a separate battery pack.
• Or run the battery down completely if it is integral and then
switch off.
• Unplug the charger before cleaning it. Your charger does not
require any maintenance apart from regular cleaning.
• Regularly clean the ventilation slots in your appliance/tool/
charger using a soft brush or dry cloth.
• Regularly clean the motor housing using a damp cloth. Do not
use any abrasive or solvent-based cleaner.
• Regularly open the chuck and tap it to remove any dust from
the interior (when fitted).
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in the new plug.
• Connect the blue lead to the neutral terminal.
WARNING! No connection is to be made to the earth
terminal. Follow the fitting instructions supplied with good quality
. The
1
plugs. Recommended fuse: 5 A.
Protecting the environment
2
and
Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
household waste. Products and batteries contain
materials that can be recovered or recycled reducing the
demand for raw materials.
Please recycle electrical products and batteries according to
local provisions.
Further information is available at www.2helpU.com.
Technical data
3
Voltage
Rated power
No-load speed
Impact rate
Weight
Max. drilling capacity
Concrete
Steel
Wood
BEh550 level of sound pressure according to En 62841:
BEh710 level of sound pressure according to En 62841:
BEh550 Vibration total values (triax vector sum) according to
Impact drilling into concrete (a
BEh550 Type2
V
230
AC
W
550
min
-1
0 ~ 2800
min
0 ~ 47600
-1
kg
1.7
mm
13
mm
13
mm
25
Sound pressure (L
) 96.5 dB(A), uncertainty (K) 5 dB(A)
pA
Sound power (L
) 104.5 dB(A), uncertainty (K) 5 dB(A)
WA
Sound pressure (L
) 98.5 dB(A), uncertainty (K) 5 dB(A)
pA
Sound power (L
) 106.5 dB(A), uncertainty (K) 5 dB(A)
WA
En 62841:
) 14.8 m/s
2
, uncertainty (K) 1.5 m/s
h, ID
Drilling into metal (a
) 1.8 m/s
2
, uncertainty (K) 1.5 m/s
h, D
BEh710 Type2
230
710
0 ~ 2800
0 ~ 47600
1.76
13
13
25
2
2
Publicidad
