6
ū Do not overtighten screws.
ū Keep this instruction manual for future reference.
ū Use an electronic stud finder to check the wall type before
drilling and mounting.
Your wall mount type will determine the size of the screw
you use to secure the speaker to the wall mount.
Refer to the table below and
presumes use of the included wall mounting washer which
is 9mm in depth.
A:
Depth of wall bracket
plate (mm)
2
3
3.5
4
5
5.2
6
NOTE:
ū The depth of the screw hole on the speaker is 7.5mm
ū The correct screw type to use is:
Imperial: 1/4-20inch
Metric: 6.35mm diameter, 1.27mm thread pitch
Connect to power
Risk of product damage! Ensure that the power supply
voltage corresponds to the voltage printed on the back or
the underside of the unit.
Connect the power adapter to the DC IN socket of the unit
and then into a mains socket.
Connecting to your AQUOS
Wireless Surround enabled
SHARP TV
Before you can add the wireless surround speakers to your
TV, your TV will need to be connected to online services via
Wi-Fi or LAN/ethernet cable. To do this, follow the network
instructions for your model of TV.
1. To begin the pairing process, press
remote control to open the settings menu. Navigate to
<Sound> and then <Wireless Speaker>.
2. In the Wireless Speaker menu, turn <Wireless
Speaker> to "On". The TV will perform a network check.
NOTE: You will need to be connected to a 5GHz Wi-Fi network
for the best wireless speaker performance. If a 5G Wi-Fi
network is not available, a 2.4GHz network can be used. A
2.4GHz network is more prone to interference and may impact
wireless speaker performance.
3. You can start the pairing process with the left or right
rear surround speaker.
4. In the television's Wireless Speaker menu, select <Add
new rear surround speaker>. The TV will prompt
you to confirm the speakers are connected to a power
3 on page 3. The table
B:
Length of screw required
MIN~MAX (mm)
14.81~16.7
15.81~17.7
18
18
18
18
18.81~20.7
on the TV
supply and located in their final positions. Select <OK>
to begin the pairing process.
5. Short press the
button on the back of one of the
PAIR
speakers. The speaker will begin pairing with the TV.
To confirm pairing mode, the LED on the rear of the
speaker will flash green.
6. On-screen prompts will appear one after the other on
the TV which will require your input:
a. Invitation to connect.
Select <Accept> to proceed with the pairing. The
TV will confirm pairing in the bottom right corner of
the display.
Now press the
PAIR
speaker. Select <Accept> to proceed with the pairing.
Now both speakers are paired to the TV.
NOTE: Once the speakers are paired to the TV,
a firmware upgrade may be detected. If this
occurs, please allow the speakers to upgrade.
b. Left and right speaker confirmation
You will hear a tone coming from a speaker.
1. If the tone is coming from your left surround
speaker, choose <Left surround>.
2. If the tone is coming from your right surround
speaker, choose <Right surround>.
3. Select <I cannot hear a sound> if no tone is
audible.
NOTE: The left and right rear surround speaker position
is determined by your left and right side as you face
the TV.
c. Optimise wireless connection
Select <Continue> to begin the connection
optimisation process.
d. Adjust listening position
You will be invited to enter distance values between
your listening position and elements of the sound
system.
This balances each speakers output to create the
optimal sound stage.
After selecting the distance values, select
<Continue>.
NOTE: This balance only affects the speakers whilst
using the AWS system.
7. Select <Finish> to complete the pairing process.
NOTE:
ū During the pairing process, the speakers may perform an
over-the-air update. Please allow this process to finish.
ū Some of the functions and features described in this
document may change. For the latest information, please
refer to the online TV manual. You can find the online TV
manual by selecting the SHARP app from the TV's home
screen.
Setting speaker properties
Whilst in the Wireless Speaker menu, select <Left rear
surround speaker property> or <Right rear surround
speaker property>. Choose from:
Name
Allows you to change the name of the speaker.
button on the back of the other