EINHELL TE-OS 18/113 3X Li Manual De Instrucciones Original página 17

machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
4. Technical data
Motor power supply ................................ 18 V DC
Idling speed .......................................11000 min
Oscillating speed ..............................22000 min
Oscillatory circuit ..................................... 1.8 mm
Sanding area of the square sanding plate ...........
.........................................................101x113 mm
Abrasive paper size (hook-and-loop fastener) ....
.........................................................102x114 mm
Abrasive paper size (clamp fastener) ...................
.........................................................130x115 mm
Sanding area of the rectangular sanding plate ....
...........................................................80x130 mm
Abrasive paper size (hook-and-loop fastener) ....
...........................................................80x132 mm
Sanding area of the triangular sanding plate .......
.................................................150x150x100 mm
Abrasive paper size (hook-and-loop fastener) ....
.................................................150x150x100 mm
Weight .......................................................1.1 kg
Important!
The equipment is supplied without rechargeable
batteries and without a charger and is allowed to
be used only with the lithium-ion batteries of the
Power X-Change series!
The lithium-ion batteries of the Power X-Change
series are allowed to be charged only with Power
X-chargers.
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 62841.
L sound pressure level ..................... 82.8 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level ....................... 90.8 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Anl_TE-OS_18-113_3X_Li_SPK13.indb 17 Anl_TE-OS_18-113_3X_Li_SPK13.indb 17
GB
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 62841.
Vibration emission value a
K uncertainty = 1.5 m/s
The stated vibration emission levels and stated
noise emission values were measured in ac-
-1
cordance with a set of standardized criteria and
-1
can be used to compare one power tool with
another.
The stated vibration emission levels and stated
noise emission values can also be used to make
an initial assessment of exposure.
Warning:
The vibration and noise emission levels may vary
from the level specifi ed during actual use, depen-
ding on the way in which the power tool is used,
especially the type of workpiece it is used for.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
Limit the operating time!
All stages of the operating cycle must be conside-
red (for example, times in which the electric tools
are switched off and times in which the tool is
switched on but operates without load).
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
- 17 -
= 12.069 m/s
2
h
2
21.12.2023 09:28:55 21.12.2023 09:28:55