Publicidad
Idiomas disponibles
Idiomas disponibles
Preparations for use
1.
Standing time
After the refrigerator is properly installed and well cleaned, do not switch it on immediately. Make sure to energize the
refrigerator after more than 1 hour of standing, so as to ensure its normal operation.
2.
Cleaning
Confirm the accessory parts inside the refrigerator and wipe the inside with a soft cloth.
3.
Power-on
Insert the plug into the solid socket to start the compressor. After 1 hour, open the freezer door, if the temperature inside
the freezer compartment drops obviously, it indicates the refrigeration system is working normally.
4.
Storage of food
After the refrigerator runs for a period of time, the internal temperature of the refrigerator will be automatically controlled
according to the user's temperature setting. After the refrigerator is fully cooled, put in foods, which usually need 2~3
hours to be fully cooled. In summer, when the temperature is high, it takes more than 4 hours for the foods to be fully
cooled (Try to open the refrigerator door as less as possible before the internal temperature cools down).
If the refrigerator is installed in the moisture place, make sure to check whether the ground wire and leakage circuit
breaker are normal. If vibration noises are produced due to the refrigerator contacting the wall or if the wall gets blackened
by air convection around the compressor, move the refrigerator away from the wall. Setting up the
refrigerator may cause jamming noise or image chaos to the mobile phone, fixed-line telephone, radio
receiver, television set surrounding it, so try to keep the refrigerator as far away as possible in such
case.
XII.
Functions
When the refrigerator system is connected to power supply for the first time, all icons on the display
panel gets illuminated for 2s. When all the doors are close, the display gets extinguished
automatically if no key operation within 3 minutes. When the display is off, it will light up if any door is
opened or any key is pressed.
The following key operations are valid only when the keys are unlocked and gets illuminated on the
display.
★Temp. setting
1）Fridge temperature setting
Press the "Fridge" button, with the fridge temperature digits flickering, and then press the "Fridge"
key to adjust the temperature, finally press the
The fridge temperature setting cycles as following:
4℃→5℃→6℃→7℃→8℃→OFF→2℃→3℃→4℃；
OFF refers to Fridge Off, and when OFF takes effect, the fridge will stop cooling.
Take foods out of the fridge compartment before setting this function.
2）Freezer temperature setting
Press the "Freezer" button, with the freezer temperature digits flickering, and then press the
"Freezer" key to adjust the temperature, finally press the
setting.
The freezer temperature setting cycles as following:
-18℃→-17℃→-16℃→-24℃→-23℃→-22℃→-21℃→-20℃→-19℃→-18℃
★ Smart ECO
1） When the "Smart ECO" function is enabled, the temperature of the fresh food compartment is controlled at 4 ℃, and
that of the freezer compartment at - 18 ℃, so that foods can be stored in the best condition while the refrigerator is
running more efficiently and with better performance.
Under the " Smart ECO " mode, the fresh food compartment temperature and the freezer compartment
temperature are subject to no change.
2）Enabling the "Smart ECO" function
Press the "Function" key to select "Smart ECO" until the corresponding icon gets flickering, and then press the
key within 5s for confirmation. If the "OK" is not pressed within 5s, the setting will be invalidated.
"OK"
3）Exiting the "Smart ECO" function
Under the "Smart ECO" mode, press the "Function" key to select "Smart ECO" until the corresponding gets
flickering, and then press the
When the "Vacation" or "Fast Freezing" or "Fast Cooling" function is enabled, the "Smart ECO" function
will be disabled automatically.
★ Fast Cooling
1) When this function is enabled, the fridge temperature is automatically set at 2℃, with the temperature reduced in the
rapid manner, so that foods can be kept in fresh condition with their nutrition not lost.
Under the "Fast Cooling" mode, the fridge temperature is subject to no adjustment.
to validate the above temperature setting.
"OK"
"OK"
key for confirmation. The "Smart ECO" function will get exited.
"OK"
to validate the above temperature
Publicidad
