Publicidad
Idiomas disponibles
Idiomas disponibles
8.5
Inserting/removing the battery
(23) in the battery mount (4)
(Fig. 6)
Inserting the battery
1. Push the battery (23) into the battery mount (4). The
battery (23) clicks into place audibly.
Removing the battery
1. Press the unlock button (22) of the battery (23) and
remove it from the battery mount (4).
8.6
Test run
Note:
Before the first work and after each tool attachment
change, carry out a test run without load. Switch off the
product immediately if the tool attachment runs out of
round, there is considerable vibration or abnormal nois-
es are heard.
1. Before operation, check whether the tool attach-
ment is properly attached, i.e. centred in the chuck
(11).
9
Operation
The cordless rechargeable battery jigsaw has a pendu-
lum lifting device, a working light and a parallel stop.
The latches for mitre angles enable precise working.
Please refer to the following descriptions for the func-
tion of the controls.
WARNING
Danger of injury!
Remove the battery from the power tool before carry-
ing out any work on the power tool (e.g. maintenance,
tool change, etc.) and when transporting and storing
it. There is a risk of injury if the on/off switch is oper-
ated unintentionally.
ATTENTION
Make sure that the ambient temperature does not ex-
ceed 50°C and does not fall below -20°C during work.
ATTENTION
The product is part of the 20V gomag series and may
only be operated with batteries of this series. Batter-
ies may only be charged with battery chargers of this
series. Observe the manufacturer's instructions.
9.1
On/Off switch (2) (Fig. 1)
The desired stroke rate can be controlled in 6 steps via
the speed control (1) on the product head.
28 | GB
Note:
The required stroke rate depends on the material and
the working conditions, and can be determined by prac-
tical trials.
Level 1
Level 6
Switching on
1. Push the ON/OFF switch (2) into position I to switch
the product on
Switching off
1. Push the ON/OFF switch (2) into position 0 to
switch off the device.
9.1.1
This product is equipped with an LED work lamp to illu-
minate the immediate work area and improve visibility
in poorly lit environments.
CAUTION
Do not look directly into the LED work lamp or the
light source.
1. The LED work lamp (14) lights up automatically as
soon as the product is switched on.
Note:
The LED work lamp remains lit up for approx. 10 sec-
onds after the product is switched off.
9.2
Setting the mitre angle (Fig. 1, 7)
Note:
Use of the chip guard is not possible with a mitre cut.
1. Remove the chip guard (19) and the angle adapter
(16).
2. Loosen the Allen screw (7) with the Allen key (18).
3. Pull the base plate (6) back slightly.
4. Set the base plate (6) to the desired position (-45° --
+45°).
There are a total of 7 levels that can be set (-45°,
-30°, -15°, 0°, 15°, 30° and 45°).
5. Slide the base plate (6) forward into one of the latch
stops.
6. Tighten the Allen screw (7) with the Allen key (18).
9.3
Setting the pendulum stroke
(Fig. 8)
With the pendulum stroke switch (5) it is possible to set
the pendulum movement of the saw blade (15).
The following positions are available for the pendulum
stroke switch (5):
0 -
No stroke
1 -
Low stroke
2 -
Moderate stroke
3 -
Powerful stroke
www.scheppach.com
lowest speed
highest speed
LED work lamp (14) (Fig. 1)
Publicidad
