Publicidad
Idiomas disponibles
Idiomas disponibles
11. Let the blade reach full speed before contacting
the workpiece. This will reduce the risk of the
workpiece being thrown.
12. Place the base plate on the workpiece, except for
plunge cuts.
13. Move the product slowly along the pre-drawn line,
pressing the base plate firmly against the work-
piece.
14. Do not exert excessive pressure on the product. Let
the product do the work.
15. Always switch the product off before placing it
down and wait until the product has come to a
standstill.
11 Cleaning and maintenance
WARNING
Have maintenance and repair tasks that are
not described in this operating manual, car-
ried out by a specialist workshop. Use only
original spare parts.
There is a risk of accident! Always perform
maintenance and cleaning work with the
battery removed. There is a danger of inju-
ry! Let the product cool down before all
maintenance and cleaning tasks. Elements
of the engine are hot. There is a danger of
injury and burning!
The product can start unexpectedly and cause inju-
ries.
–
Remove the battery.
–
Allow the product to cool down.
–
Remove the tool attachment.
11.1
Cleaning
1. Keep protective devices, air vents and the motor
housing as free of dust and dirt as possible. Rub the
product clean with a clean cloth or blow it off with
compressed air at low pressure. We recommend
that you clean the product directly after every use.
2. Ventilation openings must always be free.
3. Do not use any cleaning products or solvents; they
could attack the plastic parts of the product. Make
sure that no water can penetrate the product interi-
or.
4. Always keep the product clean, dry and free from oil
or grease. Remove dust after each use and before
storage.
5. If necessary, clean the saw blade holder with a
brush or by blowing it out with compressed air.
6. Wipe any dirt off the lens with a dry cloth. Be careful
to avoid scratching the LED lamp as this can se-
verely reduce the light intensity.
30 | GB
11.2
Maintenance
1. Check the saw blade for obvious defects before
each use and replace blunt, bent or otherwise dam-
aged saw blades.
12 Storage
Preparation for storage
1. Remove the battery.
2. Clean and check the product for damage.
Store the product and its accessories in a dark, dry and
frost-free place that is inaccessible to children.
The optimum storage temperature is between 5°C and
30˚C.
Store the product in its original packaging.
Cover the product to protect it from dust or moisture.
Store the operating manual with the product.
13 Repair & ordering spare parts
With this product, it is necessary to note that the follow-
ing parts are subject to natural or usage-related wear,
or that the following parts are required as consumables.
ATTENTION
According to the German Product Liability Act, no lia-
bility is accepted for damage caused by improper re-
pairs or by not using original spare parts.
Such work should be performed by a customer ser-
vice centre or an authorised specialists. The same
applies to accessory parts.
Spare parts and accessories can be obtained from our
Service Centre. To do this, scan the QR code on the
front page.
13.1
Ordering spare parts
Please provide the following information when ordering
spare parts:
• Model designation
• Item number
• Type plate data
Spare parts / accessories
Battery GO-ABP 2.0 item no.:
Battery GO-ABP 4.0 item no.:
Battery charger GO-BC 2.4 item no.:
Battery charger GO-BC 4.5 item no.:
Battery charger GO-BC 2.4 twin item no.: 7909201718
Battery charger GO-BC 4.5 twin item no.: 7909201719
StarterKit GO-SK2.0 item no.:
StarterKit GO-SK4.0 item no.:
www.scheppach.com
7909201714
7909201715
7909201716
7909201717
7909201725
7909201726
Publicidad
