Descargar Imprimir esta página

Mi-T-M Corporation THE JOB PRO JP Serie Manual Del Operador página 12

Ocultar thumbs Ver también para THE JOB PRO JP Serie:

Publicidad

Idiomas disponibles

Idiomas disponibles

WARNING RISK OF
EXPLOSION!
DO NOT OPERATE UNIT IN AN
AREA WHERE FLAMMABLE
GAS VAPORS MAY BE PRES-
ENT. AN ELECTRIC SPARK
MAY CAUSE AN EXPLOSION.
RISK OF BURSTING!
DO NOT STORE / OPERATE
UNIT IN A FREEZING ENVI-
RONMENT.
DANGER RISK OF
ELECTROCUTION!
THIS UNIT MUST BE CON-
NECTED TO A PROPERLY
GROUNDED OUTLET. DO NOT
USE AN ADAPTER OR RE-
MOVE THE THIRD GROUND-
ING PRONG.
WARNING RISK OF
ELECTROCUTION!
TO REDUCE THE RISK OF
ELECTROCUTION, KEEP ALL
CONNECTIONS DRY AND
OFF THE GROUND. DO NOT
TOUCH PLUG WITH WET
HANDS.
12
INSTALLATION & PREPARATION
ATTIRE:
Proper attire is essential to your safety. It is advised to utilize whatever
means necessary to protect eyes, ears, and skin. Additional safety attire
(such as respiratory mask) may be required when using detergent cleaning
agents with this washer.
SETUP:
1. This unit should only be placed on a level surface to ensure proper lubrication
for the water pump while operating. NEVER spray water directly on the
unit!
2. Do not place unit in an area:
a. where there is evidence of oil or gas leaks.
b. where flammable gas vapors may be present.
3. Do not allow the unit to be exposed to rain, snow or freezing temperatures.
If any part of the unit becomes frozen; excessive pressure may build up
in the unit which could cause it to burst, resulting in possible serious injury
to the operator or bystanders.
4. Before each use, be certain the oil level is in the center of the sight glass.
If low, fill with Mi-T-M pump oil (#AW-4085-0016). DO NOT OVERFILL!
POWER CORD CONNECTION:
1. Make certain the motor switch is in the "OFF" position.
2. Ensure electrical supply is identical to the specifications listed on the
pressure washer data plate.
3. GROUNDING INSTRUCTIONS: This product must be grounded. If it should
malfunction or breakdown, grounding provides a path of least resistance for
electric current to reduce the risk of electric shock. This product is equipped
with a cord having an equipment-grounding conductor. The plug must be
plugged into an appropriate outlet that is properly installed and grounded
in accordance with all local codes and ordinances.
4. DANGER: Improper connection of the equipment-grounding conductor
can result in a risk of electrocution. Check with a qualified electrician or
service personnel if you are in doubt as to whether the outlet is properly
grounded. Do not modify the plug - if it will not fit the outlet, have a proper
outlet installed by a qualified electrician. Do not use any type of adaptor
with this product.
5. GROUND FAULT CIRCUIT INTERRUPTER PROTECTION:
a. SINGLE PHASE: If this pressure washer is provided with a Ground
Fault Circuit Interrupter (GFCI) built into the plug or the power supply
cord, test the GFCI each time it is plugged into an outlet according to
instructions on the GFCI. DO NOT use the pressure washer if the test
fails! The GFCI provides additional protection from the risk of electric
shock. Should replacement of the plug or cord become necessary, use
only identical replacement parts that include GFCI protection.
b. SINGLE PHASE: If this pressure washer is not provided with a GFCI,
this pressure washer should only be connected to a receptacle that
is protected by a Ground Fault Circuit Interrupter (GFCI) to comply with
the National Electric Code (NFPA 70) and to provide additional protection
from the risk of electric shock.
c. THREE PHASE: These pressure washers are not provided with GFCI
protection.
6. EXTENSION CORDS: Mi-T-M DOES NOT RECOMMEND THE USE OF
EXTENSION CORDS! If use of an extension cord is unavoidable, it must
be plugged into a GFCI found in circuit boxes or protected receptacles.
When using an extension cord, consult a qualified electrician to determine
the proper wire gauge needed for the length of the extension cord.
Mi-T-M JP-Electric Operator's Manual

Publicidad

loading