Publicidad
Idiomas disponibles
Idiomas disponibles
Operations & Parts Manual
General Safety Information
Read Operating Instructions
Always become familiar with all the instructions and
warnings before operating any pneumatic tool.
Always Wear Approved Eye protection
Impact resistant eye protection should meet or exceed
the standards as set forth in the United States ANSI
Z87.1, Occupational and Educational Eye and Face
Protection. Look for the marking Z87.1 on your eye
protection to insure that it is an approved style. For
further information, ANSI Z87.1. Occupational and
Educational Eye and Face Protection, is available from
the American National Standards Institute, Inc., 11 West
nd
42
Street, New York, NY10036.
Hearing Protection is Recommended
Hearing protection should be used when the noise level
exposure equals or exceeds an 8 hour time-weighted
average sound level of 85dBA. Process noises, reflective
surfaces, other tools being operated nearby, all add to the
noise level present in your work area. If you are unable to
determine your noise level exposure, we recommend the
use of hearing protection.
Use a face mask/respirator when spraying
Always spray in a well ventilated area to prevent health
and fire hazards.
Avoid Prolonged Exposure to Vibration
Pneumatic tools can vibrate during use. Prolonged
exposure to vibration or very repetitive hand and arm
movements, can cause injury. Stop using any tool if
discomfort, tingling feeling or pain occurs. You should
consult your physician before resuming use of the tool.
90 PSIG Maximum
Husky tools are designed to operate at an air pressure of
90 pounds per square inch gauge pressure (90 PSIG)
maximum, at the tool. Use of higher air pressure can, and
may cause injury. Also use of higher air pressure places
the internal components under loads and stresses they
were not designed for, causing premature tool failure.
The air supply should be clean and dry, preferably
lubricated. For best results drain the moisture from your
compressor daily.
WARNING:
SOME DUST CREATED BY POWER SANDING,
SAWING,
GRINDING,
CONSTUCTION ACTIVITIES CONTAINS CHEMICALS
KNOWN TO CAUSE CANCER, BIRTH DEFECTS OR
REPRODUCTIVE
HARM.
THESE CHEMICALS ARE:
LEAD FROM LEAD-BASED PAINTS
CRYSTALLINE SILICA FROM BRICKS, CEMENT AND
OTHER MASONRY PRODUCTS
ARSENIC AND CHROMIUM FROM CHEMICALLY
THREAD LUMBER
4
DRILLING,
AND
OTHER
SOME
EXAMPLES
OF
YOUR
RISK
FROM
DEPENDING ON HOW OFTEN YOU DO THIS TYPE OF
WORK. TO REDUCE YOUR EXPOSURE TO THESE
CHEMICALS, WORK IN A WELL VENTILATED AREA AND
WORK WITH APPROVED SAFETY EQUIPMENT SUCH AS
THOSE DUST MASKS THAT ARE SPECIALLY DESIGNED TO
FILTER OUT MICROSCOPIC PARTICLES.
Specific Tool Safety Information
HVLP Gravity Feed Spray Gun
Do not spray flammable materials
Never aim air spray gun at people. Solvents and
thinners would cause serious injury.
Die Grinder Accessories
Use Only Recommended Grinding Stones
Use Tool only after inspection of stones, collet and hoses. Repair
or replace worn items before use. Only use accessories of the
correct size for the tool. The grinding stones' shank should be to
within size of the collet nut to prevent vibration while operating the
tool.
Use Only Recommended Sanding Drum and Sleeves
Use Tool only after inspection of sanding drum, sanding rolls,
collet and hoses. Repair or replace worn items before use. Only
use accessories of the correct size for the tool. The sanding
drum's shank should be to within sizes of the collet nut to prevent
vibration while operating the tool.
Installation
Always use clean dry air. Excessive moisture and dirt will greatly
reduce the life of any air motor. We recommend the installation of
an in-line filter-regulator-lubricator as close to the tool as possible.
A 3/8" air hose is required up to a length of 8 ft. If more length is
required a 1/2" air hose should be connected to the 3/8" hose to
ensure the tool had the necessary air supply. Be sure all hoses
and fittings are the correct size and tightly secured.
Pre-Operation
Before the tool is connected to the air supply, clear the air hose of
accumulated dust and moisture. Before removing a tool for
service or changing accessories, make sure the air line is shut-off
and drained of air. This will prevent the tool from operating if the
tool is accidentally engaged.
Model No. CAT827
THESE
EXPOSURES
VARIES,
Publicidad
