Publicidad
Idiomas disponibles
Idiomas disponibles
12
XENYX QX1202USB/QX1002USB
XENYX QX1202USB/QX1002USB Controls
(EN) Step 2: Controls
This chapter describes the various control elements
of your mixing console. All controls, switches and
connectors will be discussed in detail.
(1) MIC – Each mono input channel offers a
balanced microphone input via the XLR
connector and also features switchable
+48 V phantom power supply for condenser
microphones. The XENYX preamps provide
undistorted and noisefree gain as is typically
known only from costly outboard preamps.
(2) LINE IN – Each mono input also features
a balanced line input on a ¼" connector.
Unbalanced devices (mono jacks) can also be
connected to these inputs. Please remember
that you can only use either the microphone
or the line input of a channel at any one time.
You can never use both simultaneously!
(3) GAIN – Use the GAIN control to adjust the
input gain. This control should always be
turned fully counterclockwise whenever you
connect or disconnect a signal source to one
of the inputs.
(4) EQ – All mono input channels include a
3-band equalizer. All bands provide boost
or cut of up to 15 dB. In the central position,
the equalizer is inactive.
(5) LOW CUT – In addition, the mono channels
are equipped with a steep LOW CUT filter
designed to eliminate unwanted low-
frequency signal components.
(6) FX – FX sends enable you to feed signals via
a variable control from one or more channels
and sum these signals to a bus. The bus
appears at the console's FX send output and
can be fed from there to an external effects
device. The return from the effects unit is
then brought back into the console on the
stereo channels. Each FX send is mono and
features up to +15 dB gain. In the QX1002USB/
QX1202USB, the FX send is routed directly to
the built-in effects processor. To make sure
that the effects processor receives an input
signal, you shouldn't turn this control all the
way to the left (-∞).
(7) PAN – The PAN control determines the
position of the channel signal within
the stereo image. This control features
a constant-power characteristic, which
means the signal is always maintained at a
constant level, irrespective of position in the
stereo panorama.
(8) LEVEL – The LEVEL control determines the
level of the channel signal in the main mix.
(9) CLIP – The CLIP LED's of the mono channels
illuminate when the input signal is driven
too high, which could cause distortion. If this
happens, use the GAIN control to reduce
the preamp level until the LED does not
light anymore.
LINE IN – Each stereo channel has two
(10)
balanced line level inputs on ¼" jacks for left
and right channels. If only the jack marked "L"
(left) is used, the channel operates in mono.
The stereo channels are designed to handle
typical line level signals. Both inputs will also
accept unbalanced jacks.
FX – The FX sends of the stereo channels
(11)
function similar to those of the mono
channels. However, since the FX send buses
are both mono, a mono sum is first taken from
the stereo input before it is sent to the FX bus.
BAL – The BAL(ANCE) control determines the
(12)
levels of left and right input signals relative
to each other before both signals are then
routed to the main stereo mix bus. If a channel
is operated in mono via the left line input,
this control has the same function as the PAN
control used in the mono channels.
+4/-10 – The stereo inputs of the
(13)
XENYX QX1002USB and QX1202USB have
an input sensitivity switch which selects
between +4 dBu and -10 dBV. At -10 dBV
(home-recording level), the input is more
sensitive (requires less level to drive it) than at
+4 dBu (studio level).
FX TO MAIN – The FX TO MAIN control feeds
(14)
the effects signal into the main mix. If the
control is turned all the way counterclockwise,
no effects signal is present in the sum signal of
the mixing console.
FX SEND – The FX SEND connector outputs
(15)
the signal you picked up from the individual
channels using the FX controls. You can
connect this to the input of an external
effects device in order to process the FX bus'
master signal. Once an effects mix is created,
the processed signal can then be routed
from the effects device outputs back into a
stereo input.
PHONES/CONTROL ROOM – The stereo
LEVEL INDICATOR – The high-precision
(16)
(25)
PHONES jack (at the top of the connector
4-segment display accurately displays the
panel) is where you connect headphones.
relevant signal level.
The unbalanced CTRL ROOM OUT jacks carry
SIGNAL and CLIP LED – The SIGNAL LED on
(26)
the summed effects and main mix signals, as
the effects module shows the presence of a
well as soloed channel signals. The PHONES/
signal whose level is high enough. This LED
CONTROL ROOM control adjusts the level of
should always be on. However, make sure
both headphones and main monitor outputs.
that the CLIP LED lights up only sporadically.
MAIN MIX – The MAIN OUT connectors are
If it is lit constantly, you are overdriving the
(17)
balanced mono jacks. The main mix signal
effects processor, which leads to unpleasant
appears here at a level of 0 dBu. The MAIN MIX
distortion. If this occurs, turn the FX controls
fader adjusts the volume of these outputs.
down somewhat.
CD/TAPE INPUT – The CD/TAPE INPUTs
PROGRAM – The PROGRAM control has two
(18)
(27)
are used to bring an external signal source
functions: by turning the PROGRAM control,
(e.g. CD player, tape deck, etc.) into the
you dial the number of an effect. The number
console. They can also be used as a standard
of the preset you just dialed up blinks in the
stereo line input, so the output of a second
display. To confirm your selection, press the
XENYX or BEHRINGER ULTRALINK PRO MX882
PROGRAM control; the blinking stops.
can be connected.
COMP – This knob adjusts the amount of
(28)
CD/TAPE OUTPUT – These connectors are
compression effect on the channel.
(19)
wired in parallel with the MAIN OUT and carry
PHANTOM – Press this button to send +48 V
(29)
the main mix signal (unbalanced). Connect
of phantom power to the XLR inputs for use
the CD/TAPE OUTPUT to the inputs of your
with condenser microphones.
recording device. The output level is adjusted
via the high-precision MAIN MIX fader.
USB CONNECTOR – Connect your mixer to a
(30)
computer using a standard USB cable.
USB/2-TR TO PHONES/CTRL RM
(20)
button routes USB/2-Track playback to
AC POWER IN – Connect the included power
(31)
PHONES/CTRL ROOM.
cable here.
USB/2-TR TO MAIN MIX button routes
(21)
!
USB/2-Track playback to MAIN MIX and mutes
The mixer cannot be bus-powered via USB. Always
the 2-TR OUT/USB recording signal.
use the included power adapter to supply power to
FX TO CTRL ROOM – If you want to monitor
the mixer.
(22)
only the FX send signal in your headphones
or monitor speaker(s), press the FX TO CTRL
switch. This mutes the main mix signal while
routing the FX SEND output to the monitor(s).
+48 V – The +48 V LED lights up when
(23)
phantom power is on. The PHANTOM switch
activates the phantom power supply on the
XLR connectors of all mono channels.
POWER – The POWER LED indicates that the
(24)
console is powered on.
13
Quick Start Guide
Publicidad
