Publicidad
Idiomas disponibles
Idiomas disponibles
12
FOUR LFO
FOUR LFO Controls
(15) DIVIDE LED – this LED is lit when
the FOUR LFO is in Divide mode.
(16) RESET/SYNC 1 – a gate or clock
applied to this socket causes
different actions according to mode:
• In SYNC mode it will
synchronize LFO 1 to the
external clock.
• In RESET mode when the LFOs
are free-running it will reset
the waveform cycle of LFO 1.
• In RESET mode when the LFOs
are in QUAD, PHASE or DIVIDE it
will reset the waveform cycles
of all four LFOs.
(17) RESET/SYNC 2 – a gate or clock
applied to this socket causes
different actions according to mode:
• In SYNC mode it will
synchronize LFO 2 to the
external clock.
• In RESET mode when the LFOs
are free-running it will reset
the waveform cycle of LFO 2.
• In RESET mode when the LFOs
are in QUAD, PHASE or DIVIDE it
will pause all four LFOs.
(18) RESET/SYNC 3 – a gate or clock
applied to this socket causes
different actions according to mode:
• In SYNC mode it will
synchronize LFO 3 to the
external clock.
• In RESET mode when the LFOs
are free-running it will reset
the waveform cycle of LFO 3.
• In RESET mode when the LFOs
are in QUAD, PHASE or DIVIDE it
will reverse all four LFOs.
(19) RESET/SYNC 4 – a gate or clock
applied to this socket causes
different actions according
to mode:
• In SYNC mode it will
synchronize LFO 4 to the
external clock.
• In RESET mode when the LFOs
are free-running it will reset
the waveform cycle of LFO 4.
• In RESET mode when the LFOs
are in QUAD, PHASE or DIVIDE
it will shift the assignable
waveform to the next option
on all four LFOs, regardless of
the setting of switch 8. The
waveform selected by switch
8 will be selected again if the
mode is changed.
(20) SINE – sine wave outputs for
each LFO.
(21) ASSIGN – assignable waveform
outputs for each LFO, according to
where switch 8 is set.
(22) SQUARE – square wave outputs
for each LFO.
PRECISION
Pressing and holding button 7 puts the
FOUR LFO into precision mode to allow
precise adjustment. The LED for the
current mode will flash, and the faders
will make fine adjustments around the
centre point. When exiting precision
mode the faders will not necessarily
indicate the current setting, so the
relevant LED will continue to flash to
show this.
FIRMWARE UPDATE
On the edge of the circuit board next
to the mode switch (6) there is a micro
USB socket for updating the FOUR
LED's firmware, using the SynthTribe
application.
HINTS AND TIPS
• Use the output of one LFO
to modulate the selected
parameter of another. Or
cascade your modulation.
• In free-running mode use a
square wave from one LFO to
reset another.
Quick Start Guide
(ES) Controles
(1) FADER 1 – este fader tiene dos
funciones: en el modo autónomo
o "free-running" ajusta la
frecuencia para el LFO 1; en
caso contrario actúa como fader
master de los otros tres faders
para servir como referencia.
(2) FADER 2 – en el modo autónomo
o "free-running" actúa como un
control de frecuencia para LFO 2;
en caso contrario actúa como un
ajuste de desfase con respecto al
master para el LFO 2.
(3) FADER 3 – como el fader 2 pero
para el LFO 3.
(4) FADER 4 – como el fader 2 pero
para el LFO 4.
(5) FREE LED – cuando este piloto
esté encendido, los CUATRO LFO
actuarán en el modo autónomo o
"free-running".
(6) MODE – use este interruptor para
elegir el funcionamiento de las
tomas 16 a 19. En el modo RESET
un efecto de puerta aplicado a
esas tomas hará que las formas de
onda de los LFO sean reiniciadas;
en el modo SYNC, los LFO se
sincronizarán a una señal de reloj
enviada a esas tomas.
13
Publicidad
