Publicidad
Idiomas disponibles
Idiomas disponibles
3.
Add water in the inner stainless-steel water tank without exceeding the maximum capacity.
NOTE: Ensure that the minimum quantity of water is at least 1/5 full. DO NOT fill the appliance over
max line, as water may spill out of the water outlet when boiling.
4.
Close the lid securely until the base and the lid are properly aligned. You can also hear a
"click" when lid is properly closed.
NOTE: Ensure the sealing ring on the inside of the lid is properly installed before operating.
DO NOT operate if the sealing ring is damaged. Ensure that the lid is firmly closed before
plugging the power outlet.
5.
Insert the power cord into the socket outlet of the main body, then plug the power cord
into a 120 V AC wall outlet. Appliance will beep and power light will blink.
6.
Press the POWER button once, the appliance will default at 203 °F (95 °C) with BOIL function
on. The appliance will then heat the water to boil first, then maintain it at 203 °F (95 °C) once
the water cools down. The KEEP WARM indicator will illuminate when the appliance is under
the KEEP WARM condition when the preset temperature has been reached.
WARNING: When BOIL function is ON, water will not immediately drop to 113 °F (45 °C) after
it boils even if preset temperature is 113 °F (45 °C).
7.
Press TEMPERATURE button to select desired temperature from 113 °F, 131 °F, 185 °F and
203 °F (45 °C, 55 °C, 85 °C to 95 °C). The appliance will boil the water and will switch into
KEEP WARM function at the selected temperature, its corresponding indicator will stop
blinking when the selected temperature has been reached and will stay at the desired
temperature until power off.
WARNING: Use extreme caution when opening the lid as hot steam will escape and may
cause scalding. Use protective oven mitts or gloves to avoid burns or serious personal injury.
8.
During the heating process, if you do not wish to boil the water, press the BOIL button once
to deactivate the boil function. Water will heat up until selected temperature is reached and
KEEP WARM will engage. If you decide to boil the water, simply reactivate the BOIL function.
Appliance will go from KEEP WARM to HEATING until the water boils. After the water boils,
the appliance will switch back to KEEP WARM.
9.
Once the selected temperature has been reached, you may dispense water. To dispense
water, you must press the UNLOCK button followed by the DISPENSE button. The appliance
will lock itself 10 seconds after the DISPENSE button has been released. The UNLOCK
indicator light will turn OFF.
NOTE: DO NOT dispense water when the water is boiling or within 5 minutes after the
water is boiled. Avoid moving the appliance when dispensing water.
NOTE: Should you accidentally allow the appliance to operate without water, the boil-dry
protection will automatically switch it off. If this should occur, allow the appliance to cool
before filling it with cold water and re-boiling.
10.
After using the appliance, press the POWER button to turn OFF the appliance.
11.
Unplug the appliance from the electrical outlet. Allow to cool down completely before cleaning
(see CLEANING AND CARE Instructions).
8
CLEANING AND CARE
ALWAYS disconnect the appliance from the power outlet and leave it to cool down completely
before cleaning.
NEVER immerse the appliance or cord in water or allow moisture to contact these parts.
• Wipe the external housing and lid with a damp cloth or cleaner.
• DO NOT rinse the main body with water; otherwise, water may damage the electrical
components inside the body and the electrical outlet on the bottom of the body.
• Wipe the inner stainless-steel water tank with a non-abrasive sponge soaked with water
and dry thoroughly before storage.
• DO NOT use detergent for cleaning; otherwise, it will leave a bad smell.
• DO NOT use gasoline or turpentine for cleaning to avoid damaging the surface.
LID
Detach the lid completely to empty the residual water in the inner cavity by following the
operation as below:
1.
Open the lid using the lever then pull the lid upwards while pressing down on the lid latch
located behind the water dispenser.
2.
To put the lid back onto the dispenser, fix the rotation shaft of lid into the fixing slot of top lid.
NOTE: Make sure there is no water left in the inner cavity if the appliance is not used
SEALING RING
The sealing ring located on the inside of the lid needs to be cleaned frequently or replaced if it is
broken or not assembling properly to prevent the steam from leaking from the clearance of the lid.
The sealing ring can be removed directly and cleaned out.
NOTE: Before each use, ensure the sealing ring is properly installed. Ensure the lid is tightly closed
before operating.
REMOVAL OF MINERAL DEPOSITS
Mineral deposits in tap water may cause discoloration in the water tank surfaces. To remove this
build-up, use nontoxic scale/lime remover and follow its manufacturer's directions.
ALTERNATIVELY
1.
Fill the appliance with 6 cups of white vinegar and the remainder with water and let it sit
overnight. DO NOT boil.
2.
Empty the solution from the appliance. Any stains remaining inside the spout can be
removed by wiping with a damp cloth. Fill the appliance with clean water, bring to a boil and
then discard the water.
3.
Repeat Step 2, then the appliance will be ready to use.
9
Publicidad
