Publicidad
Idiomas disponibles
Idiomas disponibles
5.0
Maintenance & Cleaning
5.1
The welding helmet should be handled with care. Do not drop or place heavy objects on the ADF Filter. If the filter is
scratched or broken, it must be replaced before using again. A filter covered in dust or condensation could cause light
diffusion and significantly impair vision.
5.2
The welding helmet has an external plate (cover plate) made of polycarbonate, which has a high melting point and good
technical specifications to protect the auto-darkening filter from grease, dirt, dust and spatter. The cover plate will wear
with use and should be replaced as soon as vision is impaired. The filter viewing area can be cleaned when the front
cover plate is changed. The following cleaning methods are recommended: Wipe with a clean, dry cloth; clean with a soft,
moistened cloth; dry with a clean cloth.
5.3
If used correctly, the auto-darkening filter does not require any maintenance during its service life.
5.4
The rest of the components can be cleaned with a cloth moistened in soapy water, rinsed, and dried with a dry cloth.
6.0
Storage & Transport
6.1
Make sure that the welding helmet, auto-darkening filter, and cover plate are not damaged. The welding helmet must be
carefully transported in the original box, away from other objects and never stored near sharp objects. The storage place
should be dry, away from heat sources and out of direct sunlight, at a temperature between -4ºF-176ºF (-20ºC-80ºC). This
auto-darkening welding helmet does not contain any special or dangerous materials. It can be disposed of in the same
way as other standard electronic appliances.
7.0
Warranty
®
Sellstrom
warrants its auto-darkening filter products to be free from defects in material and workmanship for a period of
two (2) years. Sellstrom
purchase price of any product or portion thereof determined to be defective in materials or workmanship. Auto-darkening
filters that fail to perform as specified during the first two (2) years will be replaced at no charge. A copy of the original
invoice and serial number are required as proof of purchase.
Sellstrom
®
shall not be responsible for any indirect or consequential damages arising out of the use of this product. This
warranty shall be voided in its entirety on any auto-darkening filter that has been tampered with, misused, abused,
improperly maintained, used with components other than the originally intended Sellstrom
its original configuration in any manner. This warranty is made in lieu of all other warranties, express or implied, including,
but not limited to, all implied warranties of merchantability and fitness for any particular purpose. No deviation from this
manufacturer's warranty is authorized. Defective active filters within the warranty period should be reported to Sellstrom
Customer Service at 1.800.323.7402
8.0
WARNINGS!
8.1
This auto-darkening welding helmet shall only be used for arc-welding processes within the range of applications listed in
these instructions. Make sure that you select the appropriate type of filter.
8.2
The welding helmet must always be used with an auto-darkening filter, front cover plate, and rear cover plate. Do not
make any modifications to any helmet or filter.
8.3
If the auto-darkening welding helmet fails to switch from light to dark or should unexpected irregularities appear while
welding, the helmet must be replaced immediately. It is extremely important that no object (i.e. a protection hood or a
part of the work piece itself) covers the detectors or any part of the solar cells, and the working distance is not too
large, in order not to impair the functionality of the helmet.
8.4
For complete protection of the face, the helmet must be placed in the lowest position possible.
8.5
The helmet must be checked regularly and any damaged or worn parts replaced immediately.
8.6
In case of malfunction or insufficient vision, replace the auto-darkening filter immediately.
8.7
In case of dirt, damage, or impaired vision, the cover plate or auto-darkening filter must be changed immediately.
8.8
Regular inspection is recommended to check the condition of all components of the welding helmet.
8.9
The helmets and lenses are not suitable for "overhead" welding application, laser welding, or laser cutting applications.
8.10
Welding helmets are designed to protect the eyes and face from sparks, spatter, and harmful radiation under normal
welding conditions. They will not protect against severe impact hazards.
8.11
This helmet will not protect against explosive devices or corrosive liquids. Machine guards or eye splash protection must
be used when these hazards are present.
8.12
Impact resistant, primary eye protection, spectacles or goggles that meet current ANSI Z87 specifications, must be worn
at all times when using this welding helmet.
8.13
Do not use any solvents on any lens or helmets components.
8.14
The recommended operating temperature range for welding lens is 14ºF-149ºF (-10ºC-65ºC). Do not use this device
beyond these temperature limits.
8.15
Failure to follow these warnings and/or failure to follow all of the operating instructions could result in severe personal
injury.
9.0
Specifications
ADF Cartridge Size
LCD Viewing Area
Light State Shade
Dark Variable Shades
UV/IR protection
Switching time
(light to dark)
INST-WHP4000, S26400_1.17.18
®
's sole obligation under this warranty shall be, at its sole option, to repair, replace, or refund the
4.5" x 5.25" (114 x 133 x 9.5 mm)
3.94" x 3.28" (100 x 83.4 mm)
DIN 4
DIN 5-9 / 9-13
Up to DIN 15 at all times
0.08ms
®
brand products, or altered from
®
Page 5 of 6
Publicidad
