SHALL SH112006 Instrucciones De Funcionamiento página 6

GERNRAL POWER TOOL SAFETY WARNINGS
d) o not dispose of the tool by incineration.The
batteries may explode in fire.
SPECIFIC WARNINGS & SAFETY RULES
2.1 ADDITIONAL SAFETY WARNINGS
l ays assume that the tool contains fasteners.
Careless handling of the tool can result in unexpected
firing of fasteners and personal injury.
o not point the tool to ards yourself or anyone
nearby. Unexpected triggering will discharge the
fastener and can cause an injury.
Do not actuate the tool unless the tool is placed
firmly against the orkpiece. If the tool is not in
contact with the workpiece, the fastener may be
deflected away from your target.
Ensure power switch is in off position and keep
tool disconnected from the power source when the
fastener jams in the tool. While removing a jammed
fastener, the tool may be accidentally activated if it is
charged and in the on position or plugged in and
connected to its charger.
Use caution while removing a jammed fastener.
Point the tool away from self or others. The mecha-
nism may be under compression and the fastener may
be forcefully discharged while attempting to free a
jammed condition.
Do not use this tool for fastening high voltage
( ) electrical cables. It is not designed for electric
cable installation and may damage the insulation of
electric cables, thereby causing electric shock or fire
hazards.
2.2 SPECIFIC SAFETY RULES
1.Hold tool by insulated gripping surfaces
performing an operation
contact hidden wiring or its own cord. Contact
with a "live" wire will also make exposed metal parts
of the tool "live" and can shock the operator.
3.1 Layout (Fig. 1)
1.ON/OFF Switch
2.Charge port
3.Trigger
4.
Charge & battery status indicator
5.
Contact safety
6.
Staple exit
7.
Staple/nail viewing window
8.
Magazine latch
hen
here the tool may
LAYOUT AND ITEMS SUPPLIED
1.6 MAINTENANCE
a) Have your po er tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
2. no your po er tool. Read operator's manual
carefully. Learn its applications and limitations, as
well as the specific potential hazards related to this
tool. Following this rule may reduce the risk of
electric shock, fire, or serious injury.
3. l ays ear safety glasses
Everyday glasses have only impact resistant lenses.
They are NOT safety glasses. Following this rule
may reduce the risk of eye injury.
4. Protect your hearing. Wear hearing protection
during extended periods of operation. Following this
rule may reduce the risk of serious personal injury.
5. Protect your lungs. Wear a face or dust mask if
the operation is dusty. Following this rule may
reduce the risk of serious personal injury.
6. o not abuse charger cord. Never carry tool by
charger cord. Never yank cord to disconnect it from
receptacle. Keep charger cord away from heat, oil
and sharp edges, and moving parts.
7. Do not attempt to alter the tool. Your SHALL
cordless electric stapler has a tested cycling time. It
is designed to perform adequately at this rate. Any
unauthorized alteration and/or use could result in a
hazardous condition causing possible serious
personal injury. Unauthorized parts and/or tool
modification automatically voids warranty.
8. Use proper charging device. While charging, the
tool should always be supplied via a residual current
device with a rated residual current of 20 mA or less.
9.
Charger
10.Staple type change button
3.2 Items supplied
CARTON CONTENTS
• Cordless Electric Stapler
• Charger
• Original safety and operating instructions
•
Staple Remover
•
3/8" Staple * 1000 (RAPID N140 / T50)
3/8" Staple * 1000 (RAPID N53 / JT21)
3/8" Nail * 500 (RAPID N8 / 18GA)
•
Original safety and operating instructions
6
ith side shields.