Descargar Imprimir esta página

OMC IGNITE Manual Del Usuario página 6

Publicidad

Idiomas disponibles

Idiomas disponibles

VENTURI TUBES
Always keep venturi tubes clean.
Blockages in the venturi tubes caused by spiders, insects and nests
can cause a flashback fire.
Although the gas grill may still light, the backed up gas can ignite and
cause a fire around the venturi tubes at the control panel or the side
burner.
If a flashback fire occurs, turn off gas at the source immediately.
Inspect and clean the venturi tubes (main burner, side burner, rear
burner) if any of the following symptoms occur:
1.
You smell gas.
2.
Your gas grill does not reach temperature.
3.
Your gas grill heats unevenly.
4.
The burners make popping noises.
INSPECTING & CLEANING VENTURI TUBES
1.
Be sure the cylinder valve is "OFF".
2.
Once the grill is cool. R emove the burner fasteners and the top
portion of the collector box. Proceed to lift the burners from the gas
grill housing.
3.
Clean the venturi tubes with a pipe cleaner or venturi cleaning
tool (Accessory #77311).
4.
Lower the burner into position in the gas grill housing, making
sure that the venturi tubes are correctly aligned and fitted on the
orifices.
5.
Secure burners with burner fasteners. Snap top portion of collector
box back in place.
LIGHTING
LIGHTING INSTRUCTIONS
The grill must be assembled and installed as per the assembly and
installation instructions.
Ensure LP cylinder is full and properly connected to the regulator.
See: "Hose and Regulator" (pg. 5).
Ensure there are no gas leaks in the gas supply system. See: "Leak
Testing" (pg. 5).
Ensure that the venturi tubes are properly located over the gas valve
orifices. See "Venturi Tubes", (pg. 6).
Ensure that Main Burner, Side Burner and Rear Burner ignition wires
are connected.
Check that the battery has been installed in the electronic ignition.
Carefully review all instructions on the information plate attached to
the gas grill.
1.
Open lid before lighting.
2.
Do not lean over gas grill while lighting.
3.
Set control knobs to "OFF" and turn on the gas supply.
LIGHTING THE MAIN BURNER:
To light burner with the ignitor:
4.
Push and turn one main burner control knob to "HIGH."
5.
Push and hold down the ignitor.
6.
Burner should ignite within 5 seconds; turn off gas source
immediately if ignition does not occur in this timeframe.
To light burner with a match:
4.
Use the match holder and apply lit match to burner port.
5.
Push and turn right main burner control knob to "HIGH."
6.
Burner should ignite within 5 seconds; turn off gas source
immediately if ignition does not occur in this timeframe.
7.
After the first burner is lit, push and turn the adjacent main burner
control knob to "HIGH" then repeat for other burners; these burners
should light automatically without the ignitor.
Note: In windy conditions, ignite each burner individually.
LIGHTING THE SIDE BURNER:
To light burner with the Ignitor:
4.
Push and turn side burner control knob to "HIGH."
5.
Push and hold the ignitor button.
6.
Burner should ignite within 5 seconds.
To light burner with a match:
4.
Apply lit match to burner ports.
5.
Push in the side burner control knob and turn to "HIGH."
6.
Burner should ignite within 5 seconds.
Note: Pots on the side burner must not exceed 9 inch (23 cm) diameter
or 15 lbs. (7 kg) in weight.
CAUTION: Check your gas grill after lighting. All burner ports should
show a 1 inch (2.5cm) flame on "HIGH".
BURNER
BURNER PORTS
If any of the following symptoms occur there is probably a blockage
in the venturi tubes. Shut off gas at once and clean the venturi tubes.
See "Venturi Tubes" (pg. 6).
You smell gas
A flashback fire occurs
Your gas grill heats unevenly
The burners make popping noises
IF BURNER DOES NOT IGNITE:
Push and turn control knob to "OFF." Wait 5 minutes then try again
with control knob set at "MEDIUM"
If any burner will not light, see "Troubleshooting" (pg. 10). If problem
persists, do not attempt to operate the appliance; contact OMC,
your dealer or an approved service center
SHUTDOWN:
1.
Turn LP gas cylinder valve or gas supply valve off.
2.
Turn control knobs to "OFF."
6
CHECK FLAME

Publicidad

loading

Este manual también es adecuado para:

Flame