Black and Decker GH900 Manual De Instrucciones página 12

English

CAUTION:
the cutting line protrudes beyond the trimming blade,
cut it off so that it just reaches the blade.
1. Disconnect the plug from the power source
2. Press the release tabs
remove the spool cap from the spool housing
3. Pull the nylon line spool out and clear any broken line or
cutting debris from the spool area.
4. Fit the spool onto the appliance as described in
Replacing Spool Assembly.
Replacing Spool Assembly (Fig. M–P)

WARNING:
recommended by BLACK+DECKER for use with this
appliance could be hazardous.

WARNING:
or any accessory or attachment other than those
recommended by BLACK+DECKER on this trimmer/
edger. Serious injury or product damage may result.
Reload nylon line (either bulk or prewound replacement
spool) as shown in this manual.
UsE OnlY BlACK+DECKER REPlACEMEnT sPOOl
AF-100 or 0.065" (1.65 mm) DiAMETER ROUnD nYlOn
MOnOFilAMEnT linE. Do not use serrated or larger
diameter line or line with a shape other than round, as they
will affect the way the line feeds and overload the motor and
cause overheating. This line is available at your local dealer or
authorized service center. Do not use wire.
1. Disconnect the plug from the power source.
2. Remove battery from appliance.
3. Press the release tabs 20 on the spool cap 19 , and
remove the spool cap from the spool housing 12 .
4. Remove the empty spool 26 from the spool housing 12 .
5. Inspect the lever 22 to confirm that it is present and not
broken or bent, and it pivots freely on the mounting post.
Also confirm the metal ferrule 31 is present.
6. If the lever 22 in the base of spool housing becomes
dislodged, replace in the correct position before inserting the
new spool into the housing.
7. Remove any dirt and grass from the spool cap and
spool housing.
8. Unfasten the end of the cutting line 25 and guide the
line into the eyelet 33 .
9. Take the fully wound spool 26 and carefully slip it onto
the post 35 in the housing. Rotate the spool slightly, to
align it with the lever 22 , until it is seated.
10. The line should extend approximately 5‑3/8" (136 mm)
from the housing.
11. Inspect the spool cap 19 for cracks or excessive wear. If
any of the outer ribs are worn down to the main surface or
there are cracks present, replace the spool cap 19 .
12. Align the release tabs on the spool cap with the
slots 36 in the spool housing.
13. Snap the spool cap 19 back on by depressing release
tabs 20 and pressing it into the spool housing 12 until it
snaps securely into place.
10
To avoid appliance damage, if
on the spool cap
20 19
12
The use of any accessory not
Do not use any blades,
14. Extend the cutting line 25 from the spool housing 12
and cut so that it does extend past the cutting blade 37 .
nOTE: Make sure that cover is fully positioned. Listen for
two audible clicks to ensure both release tabs are correctly
located. Following prior instructions, power the appliance on.
In a few seconds or less you'll hear the nylon line being cut
, and
automatically to the proper length.
.
nOTE: Other replacement parts (guards, spool caps, etc.) are
available through authorized service centers. To find your
local service location call: 1-800-544-6986 or visit
www.blackanddecker.com.
Rewinding Spool from Bulk Line (Fig. Q–S)
Use Only 0.065" (1.65 mm) Diameter,
Round Line
DO nOT use larger diameter line or line with a shape other
than round.
nOTE: Hand wound spools from bulk line are likely to
become tangled more frequently than BLACK+DECKER
factory wound spools. For best results, factory wound spools
are recommended.
1. Disconnect the plug from the power source.
2. Remove the empty spool from the appliance and inspect
as described in Replacing Spool Assembly.
3. Remove any remaining cutting line from the spool.
4. Make a fold at the end of the cutting line
3/4" (19 mm). Feed the cutting line into one of the line
anchoring slots
5. Insert the 3/4" (19 mm) end of the bulk line into the
hole
29
line is pulled tight against the spool.
6. Wind the cutting line onto the spool in the direction of
the arrow on the spool. Make sure to wind the line on
neatly and in layers. Do not crisscross.
7. When the wound cutting line reaches the recesses
cut the line. DO nOT fill the spool beyond this point.
8. Fit the spool onto the appliance as described in
Replacing Spool Assembly.
MAINTENANCE

WARNING:
personal injury, turn unit off and disconnect
it from power source before making any
adjustments or removing/installing attachments
or accessories, when replacing line, or prior to
cleaning. An accidental start‑up can cause injury.
Your BLACK+DECKER power tool has been designed to
operate over a long period of time with a minimum of
maintenance. Continuous satisfactory operation depends
upon proper tool care and regular cleaning.
28 .
in the spool adjacent to the slot. Make sure the
To reduce the risk of serious
25 at about
,
30