Nolan N21 Seguridad E Instrucciones página 6

N21
VISOR (VPS LIGHT BLUE) (VPS13)
(Available as standard or accessory/spare part)
To lift up or lower the inner visor push its left side flap upwards or pull it downwards.
(Fig.1).
1 VISOR DISASSEMBLY
1.1 Lower the visor completely.
1.2 Hold the left lateral part of the visor and pull it toward the outside of the helmet
(Fig.2).
1.3 Repeat the same steps on the right side of the visor and remove it from the helmet.
2 VISOR ASSEMBLY
2.1 Insert the visor left end into the left side guide until the grip pawl is hooked in the
shell housing (Fig.2).
2.2 Repeat the same operation on the right side of the visor.
WARNING
- Make sure that the mechanisms are working properly. Open and close the visor
making sure that the mechanisms hold it in the different positions.
If necessary, repeat the above-mentioned steps
- Do not use the helmet if the visor has not been assembled properly.
- Do not remove the side mechanisms from the shell.
- Should any of the side mechanisms fail or be damaged, please refer to a Nolangroup
authorized dealer.
VISOR LOWER EDGE TRIM
The lower visor profile is moulded with a printed trim attached to the visor with fasten-
ing elements.
1 VISOR TRIM DISASSEMBLY
To release the trim from the lower edge of the visor, first remove the visor from the
helmet (see instructions above).
1.1 Pull the trim right end downwards to release the first fastening from the visor
(Fig.3).
1.2 Continue releasing the other fastenings one by one, moving towards the other end
of the visor (Fig.4).
1.3 Pull out the trim form the visor left side flap (Fig.4).
1.4 Release the trim left end and completely remove it from the visor (Fig.5).
2 VISOR TRIM ASSEMBLY
2.1 Insert the left side flap of the visor in its slot on the trim (Fig.6).
2.2 Press the trim left end against the visor to attach it to the relevant fastening ele-
ment (Fig.4).
2.3 Continue hooking the other fastenings one by one, moving towards the other end
10
INSTRUCTIONS FOR USE
of the visor (Fig.4).
2.4 Push the trim right end against the visor to attach it to the last fastening element
(Fig.3).
2.5 Push the trim against the visor aligning it with all the fastening elements in order
to attach it evenly along the whole visor lower edge; check that all the fastening
elements are correctly attached and that the trim and the visor fit together tightly.
Finally, fit the visor on the helmet (see instructions above).
WARNING
- Never use the helmet without having correctly assembled the visor lower edge
trim.
- Make sure that the mechanisms are working properly. Open and close the visor,
making sure that the mechanisms hold it in the different positions and check that
the visor lower edge trim does not come out of the visor. If necessary, repeat the
above-mentioned steps.
- In case of malfunctioning or damages, please contact an authorised Nolangroup
dealer.
REMOVABLE INNER COMFORT PADDING
1 INNER COMFORT PADDING DISASSEMBLY
To remove the inner comfort padding, open the visor completely (see instructions
above).
1.1 Open the chin strap (see specific instructions).
1.2 Hold the left front part of the liner and pull it upwards in order to remove the liner
flap from the support fixed to the polystyrene inner shell (Fig.7). Then repeat the
same steps for the central front and right flap
1.3 Remove the left and right sides of the comfort padding from the cavity between
the inner polystyrene shell, the outer shell and the visor side guides (Fig.8).
1.4 Unhook the left rear flap of the liner from the support fixed to the polystyrene
inner shell by slightly pulling the comfort padding towards the inside of the helmet
(Fig.9). Then repeat the same steps for the central and right flap.
1.5 Remove the chin straps from the elastic loops on the straps and the from the liner
side slots (Fig. 10A).
1.6 Completely remove the liner from the helmet.
2 INNER COMFORT PADDING ASSEMBLY
2.1 Insert the liner correctly into the helmet and fit it well against the base
2.2 Pull the left rectangular textile extension of the liner (Fig.10B) and insert the chin
strap into the corresponding slot in the lateral side of the liner (Fig.10A) then fold
the rectangular textile extension of the liner inside the padding. Follow the same
steps on the right side of the helmet.
2.3 Insert the right and left sides of the liner in the cavity between the inner polystyrene
shell, the outer shell and the visor side guides (Fig.8).
2.4 Insert the central rear flap of the liner into its seat on the support fixed to the poly-
styrene inner shell and push it downwards until it is completely locked. Follow the
same steps for the right and left rear flaps. (Fig.9).
N21
11
INSTRUCTIONS FOR USE