HIKVISION DS-2XC6445G0 Guia De Inicio Rapido página 16

Do not dispose of the battery into fire or a hot oven, or
mechanically crush or cut the battery, which may result in an
explosion. Do not leave the battery in an extremely high
temperature surrounding environment, which may result in an
explosion or the leakage of flammable liquid or gas. Do not subject
the battery to extremely low air pressure, which may result in an
explosion or the leakage of flammable liquid or gas. + identifies
the positive terminal(s) of equipment which is used with, or
generates direct current. - identifies the negative terminal(s) of
equipment which is used with, or generates direct current.
Fire Prevention
No naked flame sources, such as lighted candles, should be placed
on the equipment. The serial port of the equipment is used for
debugging only.
Hot Surface Prevention
CAUTION: Hot parts! Burned fingers when handling the parts. Wait
care. For device with this sticker, this device is intended for
installation in a restricted access location, access can only be
gained by service persons or by users who have been instructed
about the reasons for the restrictions applied to the location and
about any precautions that shall be taken.
Installation
Install the device according to the instructions in this manual. To
prevent injury, this device must be securely attached to the
installation surface in accordance with the installation instructions.
Never place the device in an unstable location. The device may fall,
causing serious personal injury or death. Do not install devices for
professional use in locations where children are likely to appear.
If the device is not released with a power adapter, and you need
to wire the bare cables of the device: The device external wiring
connected to the hazardous live terminals requires installation by
an instructed person. Make sure that the power has been
disconnected before you wire, install, or disassemble the device.
The power supply or device must be connected to an earthed
mains socket-outlet. High voltage for the power supply. Do not
disassemble it. If the device needs to be wired by yourself, select
the corresponding wire to supply power according to the electric
parameters labeled on the device. Strip off wire with a standard
wire stripper at corresponding position. To avoid serious
consequences, the length of stripped wire shall be appropriate,
and conductors shall not be exposed.
Power Supply
Device powered by Safety Extra-Low Voltage (SELV): The power
source should meet limited power source or PS2 requirements
according to IEC 60950-1 or IEC 62368-1 standard.
Device powered by AC mains supply voltage: The equipment must
be connected to an earthed mains socket-outlet. An appropriate
readily accessible disconnect device shall be incorporated external
Conformité à la réglementation et consignes de sécurité
Lisez soigneusement toutes les informations et instructions de ce
document avant d'utiliser l'appareil et conservez-le pour toute
référence ultérieure.
Pour plus d'informations et d'instructions sur l'appareil, veuillez
consulter notre site Internet à l'adresse
https://www.hikvision.com. Vous pouvez également consulter les
one-half hour after switching off before
handling parts. This sticker is to indicate
that the marked item can be hot and
should not be touched without taking
to the equipment. An appropriate overcurrent protective device
shall be incorporated external to the equipment, not exceeding
the specification of the building. An all-pole mains switch shall be
incorporated in the electrical installation of the building. If the
device is powered by terminals connected to the power cord,
ensure correct voltage and wiring of the terminals for connection
to mains supply. The equipment has been designed, when
required, modified for connection to an IT power distribution
system.
White Light Illuminator (If supported)
Possibly hazardous optical radiation emitted from this product. DO
NOT stare at operating light source. May be harmful to the eyes.
Wear appropriate eye protection or DO NOT turn on the white
light when you assemble, install or maintain the camera.
Transportation
Keep the device in original or similar packaging while transporting
it.
System Security
Please understand that you have the responsibility to configure all
the passwords and other security settings about the device, and
keep your user name and password.
Maintenance
If the product does not work properly, please contact your dealer
or the nearest service center. We shall not assume any
responsibility for problems caused by unauthorized repair or
maintenance.
Cleaning
Please use a soft and dry cloth when clean inside and outside
surfaces of the product cover. Do not use alkaline detergents.
Using Environment
When any laser equipment is in use, make sure that the device
lens is not exposed to the laser beam, or it may burn out. DO NOT
expose the device to high electromagnetic radiation or dusty
environments. For indoor-only device, place it in a dry and
well-ventilated environment. DO NOT aim the lens at the sun or
any other bright light. Make sure the running environment meets
the requirement of the device. DO NOT place the camera in
extremely hot, cold, dusty or damp locations, and do not expose it
to high electromagnetic radiation.
Emergency
If smoke, odor, or noise arises from the power supply or device,
immediately turn off the power, unplug the power cable, and
contact the service center.
Time Synchronization
Set up device time manually for the first time access if the local
time is not synchronized with that of the network. Visit the device
via Web browse/client software and go to time settings interface.
Reflection
Make sure that no reflective surface is too close to the device lens.
The IR light from the device may reflect back into the lens causing
reflection.
autres documents (le cas échéant) accompagnant l'appareil ou
scanner le code QR (le cas échéant) sur l'emballage pour obtenir
plus d'informations.
MENTIONS LÉGALES
 DANS LES LIMITES AUTORISÉES PAR LA LOI EN VIGUEUR, LE
PRÉSENT DOCUMENT ET LE PRODUIT DÉCRIT, AINSI QUE SON
MATÉRIEL, SES LOGICIELS ET SES MICROLOGICIELS, SONT
15
Français