Descargar Imprimir esta página

Craftsman CMCCSP20 Manual De Instrucciones página 9

Ocultar thumbs Ver también para CMCCSP20:

Publicidad

Idiomas disponibles

Idiomas disponibles


WARNING: Always check to make sure that the sleeve
is completely threaded on and that the red threads are no
longer visible. Not threading the sleeve completely on could
result in the assemblies becoming disconnected creating a
hazardous condition. Periodically check the connections to
insure that no red threads are visible.
The three assemblies which make up the pole saw are
keyed to insure correct assembly. If an assembly does not
smoothly attach to another do not force fit.
Combining the handle assembly 
assembly 
 3 
creates a pole saw that is approximately
6' (1.8 m) in length as shown in Fig. H.
To attach the handle assembly to the saw head assembly:
1. Align the groove 
on the outside of the coupling
 21 
end of the handle assembly 
inside of the coupling end of the saw head assembly 
Refer to Fig. I. Push the two sections completely together.
Refer to Fig. J.
2. Slide the threaded sleeve 
down as far as possible and rotate the sleeve clockwise
until it stops and completely covers the threads as shown in
Fig. J and  K.
Joining Center Extension to Saw Head Module and
Handle Module (Fig. A, L)

WARNING: Always check to make sure that the sleeve
is completely threaded on and that the red threads are no
longer visible. Not threading the sleeve completely on could
result in the assemblies becoming disconnected creating a
hazardous condition. Periodically check the connections to
insure that no red threads are visible.
Adding the center extension 
and saw head assembly 
 3 
approximately 9' (2.7 m) in length as shown in Fig. L.
Refer to Joining Saw Head Module to Handle Module for
directions on how to attach the middle assembly to the
handle assembly and saw head assembly.
DISASSEMBLY

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/installing
attachments or accessories. An accidental start‑up can
cause injury.
Detaching Saw Head Module (Fig. M)

WARNING: Sharp moving blade. To prevent accidental
operation, insure that battery is disconnected from the handle
and that the protective scabbard is in place on the chain
before performing the following operations. Failure to do this
could result in serious personal injury.
When detaching the assemblies, whether it is in the
two-assembly or three-assembly mode, always detach
the saw head assembly 
 3 
assembly 
 1 
on the ground and grasp the center of the saw
head assembly with one hand as shown in Fig. M. Use your
other hand to loosen the threaded sleeve and then pull the
two halves apart. Repeat this process if the center extension
was attached.
OPERATION

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/installing
attachments or accessories. An accidental start‑up can
cause injury.
 1 
to the saw head
with the tongue 
 1 
 22 
 9 
on the saw head assembly
to the handle assembly 
 2 
creates a pole saw that is
first. To do this, rest the handle
Installing and Removing the Battery Pack (Fig. N)
nOTE: For best results, make sure your battery pack is
fully charged.
To install the battery pack 
battery pack with the rails inside the tool's handle and slide
it into the handle until the battery pack is firmly seated in
the tool and ensure that it does not disengage.
To remove the battery pack from the tool, press the release
button 
 23 
and firmly pull the battery pack out of the tool
handle. Insert it into the charger.
Proper Hand Position (Fig. O)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

on the
WARNING: To reduce the risk of serious personal injury,
 3 
.
ALWAYS hold securely in anticipation of a sudden reaction.
Proper hand position requires one hand on the main
handle 
 24 
and one hand on the foam gripper 
On/Off Switch (Fig. P)
Always be sure of your footing and grip the pole saw firmly
with both hands with the thumb and fingers encircling the
handle. To turn the tool ON pull the lock button 
with your thumb and then squeeze the trigger switch 
with your fingers as shown in Figure P. (Once the tool is
running you can release the lock button.) To turn the tool
OFF, release the trigger.
Operating the Pole Saw (Fig. A)

WARNING: Read and understand all instructions. Failure
to follow all instructions listed below may result in electric
shock, fire and/or serious personal injury.
 1 

CAUTION: Always reduce the tension off the chain again
after finishing work. The chain contracts as it cools down. If it
is not slackened off, it can damage the pole saw.
iMPORTAnT: Never operate a pole saw that is damaged or
improperly adjusted or that is not completely and securely
assembled. Be sure that the saw chain 
when the trigger switch is released. Never adjust the guide
bar 
or saw chain when the motor is operating or the
 13 
battery is attached.
Pole Saw Trimming/Pruning

WARNINGS:
• Never stand directly under the limb you are cutting.
Always position yourself out of the path of falling debris.
• Always wear head, eye, foot and body protection.
Wearing body protection helps reduce the risk of injury when
operating this unit.
• Never stand on a ladder or other unstable support
while using the pole saw. Always avoid any position which
can cause you to lose your balance and cause severe injury.
• Keep other persons at least 50' (15 m) from the work
area. Distractions can cause you to lose control.
• Electrocution hazard. To prevent shock, do not operate
within 50' (15 m) of overhead electrical lines. Always check
surrounding area for hidden electrical lines.
• Do not hold pole saw switch handle above
shoulder height.
Branch Removal Hook (Fig. A)

CAUTION: The branch removal hook is not a belt hook.
Your pole saw includes a branch removal hook 
intended purpose of helping to remove small- to moderately
sized pruned branches.
English
 6 
into the tool handle, align the
 7 
.
 5 
 14 
stops moving
 18 
for the
back
 4 
9

Publicidad

loading