Descargar Imprimir esta página

sigel. GL306 Instrucciones De Montaje Y Seguridad página 6

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 12
EN
CONTENTS
Mounting instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 3
Storing this user guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 6
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 6
Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 6
Use & cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 7
Guarantee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 7
Magnets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 7
Disposal and recycling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 7
STORING THIS USER GUIDE
This user guide will help you to make the best use of your new magnetic glass board. In addition to this, it contains important information
about how to safely mount and use your magnetic glass board.
Read this user guide and make sure you have understood it before mounting and using your new magnetic glass board.
Store this user guide near your magnetic glass board. If the magnetic glass board is passed on to another user, make sure that person also
receives this user guide.
SAFETY PRECAUTIONS
The Artverum Magnetic Glass Board is made of tempered safety glass tested to EN 12150-2.
1 | Before mounting, check that there are no service pipes, e.g. for electricity, gas or water, in that part of the wall.
2 | When mounting the magnetic glass board, please ensure that it does not come into contact with sharp objects or hard surfaces such as
stone or tiles. We cannot accept any claims for resulting damage to the board. Place the board on a soft surface until it is ready to be mounted
and do not remove the protective material until it is attached to the wall.
3 | The magnetic glass board should only be mounted on an even, solid wall.
4 | Two people are required to mount the board.
SIGEL GmbH does not assume any responsibility or guarantee for boards that have been incorrectly mounted or for any resulting damage.
MOUNTING
1 | The magnetic glass board can be mounted in portrait or landscape format. The enclosed mounting rails
position of the drill holes (fig. 2).
The mounting rails
are screwed securely to the wall using anchors
4 4 5 5
Tip: Please use a spirit level to check that the mounting rails
The mounting rails
have an oblong hole that can be used to adjust their position if necessary. To do so, loosen the screw and move the
4 4 5 5
mounting rails
vertically or horizontally as required. Then tighten the screw again.
4 4 5 5
2 | Two people are required to mount the magnetic glass board.
To mount the board on the wall, hold the bottom edge with one hand and the side with the other. The magnetic glass board
onto the mounting rails
4 4 5 5
the board is securely in place before letting go. Pads on the back of the board keep it steady while it is being written on.
3 | MOUNTING SEVERAL BOARDS IN A ROW
Please note the following if mounting several boards next to each other:
When mounting the boards, make sure the edges do not knock against each other, as this can cause the board to break. SIGEL is not liable
for any damage caused in this way. Mount the first magnetic glass board as described under „Mounting" before marking the drill holes for the
next board. This will allow you to adjust the position of the additional boards to any slight inaccuracies there may be in the position of the first
board.
Anleitung artverum runde Ecken 302.indd 6
Anleitung artverum runde Ecken 302.indd 6
4 4 5 5
from top to bottom (fig. 3). Make sure that the magnetic glass board is mounted on both fittings and check that
and screws
(fig. 2).
2 2
3 3
are lined up straight.
6
make it simple to mark the
4 4 5 5
is then mounted
1 1
01.02.24 10:41
01.02.24 10:41

Publicidad

loading

Este manual también es adecuado para:

Gl305Gl304Gl303