Publicidad
Idiomas disponibles
Idiomas disponibles
English
Rewinding Spool from Bulk Line (Fig. S–W)
Use Only 0.065" (1.65 mm) Diameter,
Round Line
DO nOT use larger diameter cutting line or cutting line with
shape other than round.
nOTE: Hand wound spools from bulk line are likely to
become tangled more frequently than BLACK+DECKER
factory wound spools. For best results, factory wound spools
are recommended.
1. Remove battery pack from appliance.
2. Remove the empty spool from the appliance and inspect
as described in Replacing Spool Assembly.
3. Remove any remaining cutting line from the spool.
4. Make a fold at the end of the cutting line
3/4" (19 mm). Feed the cutting line into one of the line
anchoring slots
47
.
5. Insert the 3/4" (19 mm) end of the bulk line into the
spool hole
38
in the spool adjacent to the anchoring
slot
47
. Make sure the line is pulled tight against the spool.
6. Wind the cutting line onto the spool in the direction of
the arrow on the spool. Make sure to wind the line on neatly
and in layers. Do not crisscross.
7. When the wound cutting line reaches the recesses
cut the line. DO nOT fill the spool beyond this point.
8. Fit the spool onto the appliance as described in
Replacing Spool Assembly.
Replacing the Spool Housing with the Resin Blade
Hub (Fig. X–Z)
(BCSTRB922 Only)
1. Remove battery from appliance.
2. Locate the hex key
13
above resin blade storage
shown in Fig. X.
3. Remove the spool cap
housing
11
.
4. Insert the hex key
13
housing
11
and while grasping spool, rotate the hex
key
13
counterclockwise to remove the housing screw
5. Pull the spool housing
housing
8
as shown in Fig. Y.
6. Place the resin blade hub
on the motor housing
8
7. Place the housing screw
while holding the resin blade hub, rotate the hex key
clockwise to tighten the housing screw
Installing the Resin Blades to the Resin Blade Hub
(Fig. AA–CC)
WARNING:
those recommended by BLACK+DECKER on this trimmer/
edger. Serious injury or product damage may result.
WARNING:
cutting blades are properly mounted before starting work.
12
32
at about
in its storage area
14
located
15
on auxiliary handle
27
and spool
29
from the spool
into the hole on the spool
away from the motor
11
16
onto the keyed shaft
.
in resin blade hub
40
securely.
40
Do not use any blades other than
Always ensure that both
WARNING:
only one blade will reduce cutting performance and
may damage the unit.
WARNING:
either one wears to less than 2" (50 mm) (Fig. CC), or if
either is cracked, gouged or damaged in any way.
WARNING:
at the same time.
1. Remove battery from appliance.
2. Place the retaining hole
the post
35
align with the cutout
3. Pull the resin blade
in place. The resin blade is secured in place when you hear
an audible click and the resin blade freely pivots on the resin
blade post
4. Install the second resin blade
and 2 listed above.
5. Replace the resin blades
39
,
to less than 2" (50 mm) as shown in Fig. CC.
Replacing the Resin Blade Hub with the Spool
Housing (Fig. R–Z)
(BCSTRB922 Only)
1. Remove battery from appliance.
2. Locate the hex key
above resin blade storage
shown in Fig. X.
3. Insert the hex key
5
as
hub
16
and rotate the hex key
remove the housing screw
4. Pull the resin blade hub
housing
8
5. Remove the spool cap
housing
11
40
.
is present in the spool housing
pivots on its post
6. Place the spool housing
41
the motor housing
7. Place the housing screw
and
16
housing
11
13
tighten the screw
housing
11
8. Unfasten the end of the cutting line
line into the eyelet
9. Take the fully wound spool 29 and carefully slip it onto
the post 35 in the housing. Rotate the spool slightly, to
align it with the lever 30 , until it is seated.
10. The line should extend approximately 5-3/8" (136 mm)
from the spool housing.
11. Align the release tabs 28 on the spool cap with the
slots 36 in the spool housing.
12. Snap the spool cap 27 back on by depressing release
tabs 28 and pressing it into the spool housing 11 until it
snaps securely into place.
Operating the trimmer with
Replace both of the blades if
Always replace both blades
42
of the resin blade
and slide it onto the resin blade post
44
as shown in Fig. AA.
outwards to lock the resin blade
12
43
. It should be positioned as shown in Fig. BB.
12
12
when they reduce in length
in its storage area
13
15
on auxiliary handle
into the hole on the resin blade
13
13
.
40
16
away from the motor
.
27
and spool
. Enure the lever
with the brass ferrule
30
and the lever
11
48
.
onto the keyed shaft
11
8
.
into the hole on the spool
40
and rotate the hex key
40
securely while grasping the spool
.
.
33
12
onto
43
to
as described in steps 1
located
14
5
as
counterclockwise to
29
from the spool
31
freely
30
on
41
13
clockwise to
32
and guide the
Publicidad
