Bosch 06019F6004 Manual Original página 17

Fitting
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Charging the battery
Use only the chargers listed in the technical data. Only
u
these chargers are matched to the lithium-ion battery of
your power tool.
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
Do not continue to press the On/Off switch after the
u
power tool has automatically switched off. The battery
can be damaged.
Removing the battery (see figure A)
To remove the battery (5), press the release button (4) and
pull the battery downwards out of the power tool. Do not
use force to do this.
Changing the tool
Inserting the application tool (see figure B)
Insert the application tool all the way into the mounting (1).
Fitting the adapter (see figure C)
Remove the application tool.
Insert the adapter into the holder (1). Turn the locking ring
(14) until it audibly engages.
Inserting the application tool into the adapter GFA 12-E,
GFA 12-X (see figure D)
Insert the application tool all the way into the mounting (1).
The application tool is held in the mounting by means of a
magnet.
GFA 12-B (see figure E)
Open the drill chuck adapter (11) by turning it in direction of
rotation ➊ until the application tool can be inserted. Insert
the application tool.
Firmly tighten the sleeve of the drill chuck adapter (11) by
turning it by hand in direction of rotation ➋. This will auto-
matically lock the drill chuck.
Turning the adapter (see figure F)
Pull the locked adapter approx. 5 mm away from the power
tool. Turn the adapter to the required position and then let it
go.
Bosch Power Tools
Removing the adapter (see figure G)
Remove the application tool.
Unlock the adapter in the direction and pull it off the
holder (1).
Dust/chip extraction
The dust from materials such as lead paint, some types of
wood, minerals and metal can be harmful to human health.
Touching or breathing in this dust can trigger allergic reac-
tions and/or cause respiratory illnesses in the user or in
people in the near vicinity.
Certain dusts, such as oak or beech dust, are classified as
carcinogenic, especially in conjunction with wood treatment
additives (chromate, wood preservative). Materials contain-
ing asbestos may only be machined by specialists.
– Use a dust extraction system that is suitable for the ma-
terial wherever possible.
– Provide good ventilation at the workplace.
– It is advisable to wear a P2 filter class breathing mask.
The regulations on the material being machined that apply in
the country of use must be observed.
Avoid dust accumulation at the workplace. Dust can
u
easily ignite.
Operation
Start-up
Inserting the battery
Note: The use of batteries unsuitable for your power tool can
lead to malfunctions or damage to the power tool.
Set the rotational direction switch (6) to the middle position
to avoid unintentionally switching it on. Insert the charged
battery (5) into the handle until you feel it engage and it is
flush with the handle.
Setting the rotational direction (see figure H)
Only operate the rotational direction switch (6) when
u
the power tool is not in use.
The rotational direction switch (6) is used to change the ro-
tational direction of the power tool. However, this is not pos-
sible while the on/off switch (7) is being pressed.
Right rotation: To drill and to drive in screws, press the ro-
tational direction switch (6) through to the left stop.
Left Rotation: To loosen and unscrew screws and nuts,
press the rotational direction switch (6) through to the right
stop.
Preselecting the Torque
The torque presetting ring (2) can be used to preselect the
required torque in 15 stages. When the correct setting is
used, the application tool will be stopped when the screw is
driven flush into the material or once the set torque has been
reached. In position the overload clutch is deactivated,
e.g. for drilling.
When unscrewing screws, it may be advisable to select a
higher setting or the symbol.
English | 17
1 609 92A 8AH | (08.09.2022)