Publicidad
Idiomas disponibles
Idiomas disponibles
LED Reference
LED STATUS
Power OFF
LED function verification
Power ON
Access Point mode
Client connected
(Access Point mode)
Client disconnected
(Access Point mode)
Wi-Fi disconnected (Station mode)
Wi-Fi connected (Station mode)
IoT Hub disconnected (Station mode)
IoT Hub connected (Station mode)
Wi-Fi disabled
Low temperature
Freezing temperature
Temperature sensor error
After pressing the multifunction
button for more than 1 s but less
than 3 s with alert conditions
(Disable repeat alert)
After pressing the multifunction
button for more than 3 s but less
than 10 s (Wi-Fi ON/OFF toggle)
After pressing the multifunction
button for more than 10 s but less
than 15 s (Factory reset)
After pressing the multifunction
button for more than 15 s
(Installer Test mode)
Credential missing
(Factory calibration required)
Communication error with
sensor controller
Factory Calibration mode
End Factory Calibration mode (PASS)
Limited Warranty: Watts Regulator Co. (the "Company") warrants each product to be free from defects in material and workmanship under
normal usage for a period of one year from the date of original shipment. In the event of such defects within the warranty period, the Company
will, at its option, replace or recondition the product without charge.
THE WARRANTY SET FORTH HEREIN IS GIVEN EXPRESSLY AND IS THE ONLY WARRANTY GIVEN BY THE COMPANY WITH RESPECT TO THE
PRODUCT. THE COMPANY MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED. THE COMPANY HEREBY SPECIFICALLY DISCLAIMS ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE.
The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy for breach of warranty, and the
Company shall not be responsible for any incidental, special or consequential damages, including without limitation, lost profits or the cost of
repairing or replacing other property which is damaged if this product does not work properly, other costs resulting from labor charges, delays,
vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions, chemical, or any other circumstances over
which the Company has no control. This warranty shall be invalidated by any abuse, misuse, misapplication, improper installation or improper
maintenance or alteration of the product.
Some States do not allow limitations on how long an implied warranty lasts, and some States do not allow the exclusion or limitation of inci-
dental or consequential damages. Therefore the above limitations may not apply to you. This Limited Warranty gives you specific legal rights,
and you may have other rights that vary from State to State. You should consult applicable state laws to determine your rights. SO FAR AS
IS CONSISTENT WITH APPLICABLE STATE LAW, ANY IMPLIED WARRANTIES THAT MAY NOT BE DISCLAIMED, INCLUDING THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO ONE YEAR FROM THE
DATE OF ORIGINAL SHIPMENT.
IS-FZSensorConnectionKit 2409
GREEN
BLUE
RED
OFF
OFF
OFF
ON 1 s
ON 1 s
ON
Blink 4 Hz
Blink 2 Hz
Blink 4 Hz
Blink 2 Hz
Blink 1 Hz
Blink 1 Hz
ON
OFF
Blink 1 Hz
Blink 2 Hz
Blink 4 Hz
Solid ON
if IoT
Hub
connected
Blink 8 Hz
Blink 8 Hz
Blink 8 Hz
Blink 2 Hz Blink 2 Hz Blink 2 Hz
Blink 6 Hz
ON
ON
ON
ON
OFF
ON
1923069
Radio Frequency Safety
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
• This device may not cause harmful interference, and
• This device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur during
a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
Changes or modifications to this equipment not expressly
approved by the party responsible for compliance could void
the user's authority to operate the equipment.
ISED Compliance Statement
This device complies with the Industry Canada license-exempt
Radio Standards Specification. Operation is subject to the
following two conditions.
• This device may not cause interferences; and
• This device must accept any interference, including
interference that may cause undesired operation of
the device.
USA: T: (978) 689-6066 • Watts.com
Canada: T: (888) 208-8927 • Watts.ca
Latin America: T: (52) 55-4122-0138 • Watts.com
© 2024 Watts
Publicidad
