Descargar Imprimir esta página

Atlas Copco ETV SB33-15-10-IRC-B Información Seguridad página 3

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 20
ETV SB33-15-10-IRC-B
Technical Data
Product Data
Motor voltage
Motor power
Speed
Torque range
Weight
Battery Compatibility
Accessory
Battery, 18V (2Ah)
Battery, 18V (2,5Ah)
Battery, 18V (4Ah)
Battery, 18V (5Ah)
Charger Compatibility
Accessory
Multi-Charger, 18/36V
Ambient Temperature
Operating temperature, charge
Operating temperature, discharge
Storage temperature
Charger Temperatures
Charger operating tempera-
ture
Declarations
Liability
Many events in the operating environment may affect the
tightening process and shall require a validation of results. In
compliance with applicable standards and/or regulations, we
hereby require you to check the installed torque and rotational
direction after any event that can influence the tightening re-
sult. Examples of such events include but are not limited to:
• initial installation of the tooling system
• change of part batch, bolt, screw batch, tool, software,
configuration or environment
• change of air- or electrical connections
• change in line ergonomics, process, quality procedures or
practices
• changing of operator
18 V
1080 W
720 r/min
4 - 15 Nm (3 - 11 ft lb)
1.3 kg (2.9 lb)
Article nr.
4211 5500 11
4211 5500 12
4211 5500 21
4211 5500 22
Article Number
4211 5424 85
+5 to +40 °C
(+41 to +104 °F)
0 to +40 °C
(+32 to +104 °F)
−20 to +40 °C
(−4 to +104 °F)
+5 to +40 °C
(+41 to +104 °F)
© Atlas Copco Industrial Technique AB - 9836 6425 00
• any other change that influences the result of the tighten-
ing process
The check should:
• Ensure that the joint conditions have not changed due to
events of influence.
• Be done after initial installation, maintenance or repair of
the equipment.
• Occur at least once per shift or at another suitable fre-
quency.
EU DECLARATION OF CONFORMITY
We, Atlas Copco Industrial Technique AB, SE-105 23
STOCKHOLM SWEDEN, declare under our sole responsi-
bility that the product (with name, type and serial number, see
front page) is in conformity with the following Directive(s):
2006/42/EC, 2011/65/EU, 2014/53/EU
Harmonized standards applied:
EN 300 328 V2.2.2, EN 301 489-1 V2.1.1, EN 301 489-17
V3.1.1, EN 55014-1:2017, EN 55014-2:2015, EN
61000-6-2:2019, EN 61000-6-4:2007+A1:2011, EN
62479:2010, EN 62841-1:2015, EN 62841-2-2:2014 +
AC:2015
Authorities can request relevant technical information from:
Aleksandra Duric, Product Compliance Manager, Atlas
Copco Industrial Technique AB, SE-105 23 Stockholm Swe-
den
Stockholm, 1 September 2023
Håkan Andersson, Managing Director
Signature of issuer
Noise and Vibration Declaration Statement
• Sound pressure level <70 dB(A) , uncertainty 3 dB(A), in
accordance with ISO15744.
• Sound power level <80 dB(A) , uncertainty 3 dB(A), in
accordance with ISO15744.
• Vibration total value <2.5 m/s
cordance with ISO28927-2.
These declared values were obtained by laboratory type test-
ing in accordance with the stated standards and are suitable
for comparison with the declared values of other tools tested
in accordance with the same standards. These declared values
are not adequate for use in risk assessments and values mea-
sured in individual work places may be higher. The actual ex-
posure values and risk of harm experienced by an individual
user are unique and depend upon the way the user works, the
workpiece and the workstation design, as well upon the expo-
sure time and the physical condition of the user.
We, Atlas Copco Industrial Technique AB, cannot be held
liable for the consequences of using the declared values, in-
stead of values reflecting the actual exposure, in an individual
risk assessment in a work place situation over which we have
no control.
Safety Information
2
2
, uncertainty - m/s
, in ac-
3

Publicidad

loading

Este manual también es adecuado para:

8433303182