Wesco WS3202K 1 Serie Manual Original página 8

ASSEMBLY
1. INSTALLING THE AUXILIARY HANDLE (SEE FIG. A)
For your personal safety we recommend using the auxiliary handle
at all times.
Rotate the handgrip of the auxiliary handle clockwise to loosen the
clamping ring. Slide the clamping ring of the auxiliary handle over
the handle collar of the hammer, and rotate the handle around the
collar until the handle is in a desired working position. Rotate the
handgrip counter-clockwise to tighten the auxiliary handle in place.
WARNING: The auxiliary handle must be used during
operation.
2. INSTALLING THE DEPTH GAUGE (SEE FIG. B)
The depth gauge can be used to set a constant depth for drilling in.
Rotate the depth gauge lock screw on the top of the auxiliary handle
counter-clockwise to loosen, insert the depth gauge into the hole of
the handle. Adjust it to the desired depth. Rotate the locking screw
clockwise to tighten.
3. INSERTING AND REMOVING DRILL BIT (SEE FIG. C)
Take care that the dust protection cap is not damaged when
changing tools.
- INSERTING
Clean and lightly oil the bit before inserting. Retract back the tool
holder locking sleeve and insert the dust-free bit into the tool holder
with a twisting motion until it latches. The bit locks itself. Check the
locking by pulling on the tool.
- REMOVING
Retract back the tool holder locking sleeve and pull out the bit.
WARNING: Your new rotary hammer generates
powerful forces to get your job done quickly and
effectively. These forces may cause inferior quality SDS bits to
break and jam in the chuck. We therefore recommend that
only high quality SDS bits be used with this tool.
OPERATION
1. ON/OFF SWITCH (SEE FIG. D)
Depress the On/Off switch to start and release it to stop your tool.
2. ANTI-VIBRATION HANDLE
The anti-vibration handle reduces the vibration, making operation
more comfortable and secure.
3. DUST COVER (SEE FIG. E)
Before drilling, fit the dust cover over the drill bit.
WARNING: Always wear eye protection with this tool.
4. HAMMER DRILL FUNCTION (SEE FIG. F)
1) Adjust the hammer or chisel action selector to position "
2) Adjust the hammer or drilling action selector to position "
3) You are now set up for hammer drilling into masonry.
NOTE: Press the selector switch lock button before adjusting the
dial selector every time.
5. DRILLING FUNCTION (SEE FIG. G)
1) Adjust the hammer or chisel action selector to position "
2) Adjust the hammer or drilling action selector to position " ".
3) You are now set up for drilling function.
NOTE: Press the selector switch lock button before adjusting the
dial selector every time.
8
6. CHISEL FUNCTION (SEE FIG. H)
1) Adjust the hammer or chisel action selector to position "
2) Adjust the hammer or drilling action selector to position "
3) You are now set up for chisel work using chisel action.
NOTE: Press the selector switch lock button before adjusting the
dial selector every time.
WARNING: You must make sure that the selector switch
is positively locked in chisel mode position. If not, it
could cause a hazard.
7. LUBRICATION MACHINE (SEE FIG. I)
The gearbox is lubricated with grease. Refilling is required when
the hammer efficiency is low. Open the cover using the key and add
general purpose lithium based grease.
WARNING: Keep the container of grease away from
children.
8. SAFETY CLUTCH PROTECTION
This tool will generate high forces when use. Always hold the tool
with both hands and adopt a secure posture.
If the drill bit or chisel becomes jammed in the workpiece, the clutch
will activate stopping the tool spindle. This is normal.
Switch the machine off, loosen and remove the drill bit or chisel
from the work piece.
WARNING: Switching the machine on with the drill bit
or chisel jammed in the work piece will generate high
reaction torque and can result in injury.
WORKING HINTS FOR YOUR TOOL
1. Reduce the pressure on the drill bit when it is about to break
through. This will prevent the drill from jamming.
2. When drilling a large hole, first drill a pilot hole using a smaller
drill bit.
3. Always apply pressure to your drill bit in a straight line, and if
possible at right angles to the workpiece.
4. Never change the operating mode whilst the rotary hammer is
running.
5. Do not apply excessive pressure to the tool when chiseling.
Expressive force does not speed up the work.
MAINTAINACE
Remove the plug from the socket before carrying out any
adjustment, servicing or maintenance.
There are no user serviceable parts in your power tool.
Never use water or chemical cleaners to clean your power tool. Wipe
clean with a dry cloth. Always store your power tool in a dry place.
".
Keep the motor ventilation slots clean.Keep all working controls free
".
of dust. Occasionally you may see sparks through the ventilation
slots. This is normal and will not damage your power tool.
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons in
order to avoid a hazard.
".
".
".
EN