Publicidad
Idiomas disponibles
Idiomas disponibles
90543725 HP18V
10/10/08
7. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise
subjected to damage or stress.
8. An extension cord should not be used unless absolutely necessary. Use of improper
extension cord could result in a risk of fire, electric shock or electrocution.
a. Two-wire cords can be used with 2-wire or 3-wire extension cords. Only round
jacketed extension cords should be used, and we recommend that they be listed by
Underwriters Laboratories (U.L.). If the extension is to be used outside, the cord must
be suitable for outdoor use. Any cord marked for outdoor use can also be used for
indoor work. The letters "W" or "WA" on the cord jacket indicate that the cord is
suitable for outdoor use.
b. An extension cord must have adequate wire size (AWG or American Wire Gauge) for
safety, and to prevent loss of power and overheating. The smaller the gauge number
of the wire, the greater the capacity of the cable; that is, 16 gauge has more capacity
than 18 gauge. When using more than one extension to make up the total length, be
sure each extension contains at least the minimum wire size.
CHART FOR MINIMUM WIRE SIZE (AWG)OF EXTENSION CORDS
Total Extension Cord Length (ft)
Wire Gauge
9. Use only the supplied charger when charging your tool. The use of any other charger
could damage the tool or create a hazardous condition.
10. Use only one charger when charging.
11. Do not attempt to open the charger or the tool. There are no customer serviceable
parts inside. Return to any authorized Black & Decker service center.
12. DO NOT incinerate the tool or battery packs even if they are severely damaged or
completely worn out. The batteries can explode in a fire.
13. A small leakage of liquid from the battery pack cells may occur under extreme usage,
charging or temperature conditions. This does not indicate a failure. However, if the
outer seal is broken and this leakage gets on your skin:
a. Wash quickly with soap and water.
b. Neutralize with a mild acid such as lemon juice or vinegar.
c. If the battery pack liquid gets in your eyes, flush them with clean water for a minimum
of 10 minutes and seek immediate medical attention. MEDICAL NOTE: The liquid is a
25-35% solution of potassium hydroxide.
CHARGING THE BATTERY PACK (FIGURE 1)
THE BATTERY PACK IS NOT FULLY CHARGED AT THE FACTORY. BEFORE
ATTEMPTING TO CHARGE THE BATTERY PACK, THOROUGHLY READ ALL OF THE
SAFETY INSTRUCTIONS.
The charger is designed to use standard household 120 volt 60 Hz power.
1. Plug the charger (H) into any standard 120 Volt 60 Hz electrical outlet. NOTE: Do not
charge by means of an engine generator or DC power source. Use only 120V AC
2. Slide the charger onto the battery pack (F) as shown in figure 1 and let the battery
pack charge initially for 12 hours. After the initial charge, under normal usage, your
battery pack should be fully charged in 6 to 12 hours.
3. Unplug charger, and remove the battery pack. Place the battery pack in the tool
and be certain that it is inserted fully into the tool cavity until it "clicks" into place.
NOTE: To remove the battery pack from the drill, press down on the release button
(G) on the back of the battery pack (figure 2) and slide out.
IMPORTANT CHARGING NOTES
1. After normal usage, your battery pack should be fully charged in 6 to 12 hours. If the
battery pack is run-down completely, it may take up to 12 hours to become fully
charged. Your battery pack was sent from the factory in an uncharged condition.
Before attempting to use it, it must be charged for at least 12 hours.
2. DO NOT charge the battery pack in an air temperature below 40°F (4,5°C) or above
105°F (40,5 °C). This is important and will prevent serious damage to the battery
pack. Longest life and best performance can be obtained if battery pack is charged
when air temperature is about 75°F (24°C).
1:31 PM
Page 7
NAMEPLATE RATING AMPS – 0 – 10.0
25
50
75
(m) 7,6
15,2 22,8
18
18
16
7
100
125
150
30,4 38,1 45,7
16
14
14
Publicidad
