Shop-Vac SS11 Serie Manual Del Usuario página 4

CASTER SySTEM ASSEMBLy
Not all units are equipped with the same caster system. Follow the instructions, which
apply to your specific unit.
With Caster feet
1. With cord disconnected from receptacle and tank
cover removed, turn tank upside down so that the
bottom is facing up.
2. With a pair of scissors, trim the enclosed template
to fit your size tank. Sizes will be 11", 14" or 16"
diameters.
3. Once template is cut out, place on bottom of tank.
Align inlet arrow on template with center of inlet on
tank (figure 2).
4. If caster feet are attached together, separate by
removing webbing.
5. Take caster foot marked with the letter A and align
arrow on foot (figure 3) with arrow on template
also marked with the letter A (figure 4).
6. Place groove of foot over rim of tank and push until
the caster foot is tight against bottom of tank (figure 5).
7. Secure feet with screw and washer when provided (figure 6).
8. Insert casters into feet by placing stem of caster into holes provided. Apply pressure and
twisting motion until casters snap into place (figure 7).
9. Repeat steps 4-8 with remaining feet.
10. Return tank to upright position.
With Caster Dolly
1. You will find four casters (Figure 8) with your wet/dry vacuum. Assemble as follows:
2. With cord disconnected from receptacle and tank cover removed, turn tank upside down so
that bottom is facing up.
3. If the casters are not already installed in dolly, insert casters into bottom of dolly by placing
stem of caster into holes provided. Apply pressure and twisting motion until casters snap
into place (Figure 9).
4. Return tank to upright position.
8
Rear Wheel Dolly/Tool Holder and front Caster feet Assembly
you will find two casters (a.), two large rear wheels (b.), one axle (c.), rear dolly (d.), two
caster feet (e.) and four screws with your wet/dry vacuum. Assemble as follows:
a b
1. With cord disconnected from receptacle and tank cover removed, turn tank upside down
so that the bottom is facing up.
2. Place axle upright on a hard surface and hammer on (1) cap nut. Place (1) wheel on axle
and slide down to cap nut (figure 10). Be sure flat side of wheel hub is facing outward.
3. Slide axle through holes provided in dolly (figure 11).
Slide remaining wheel onto axle and hammer on second cap nut (figure 12).
4.
5. With a pair of scissors, trim the enclosed template to fit your size tank. Sizes will be 11",
14" or 16" diameters.
6. Once template is cut out, place on bottom of tank, align inlet arrow on template with cen-
ter of inlet on tank (figure 13).
Align cutouts in center of rear dolly with bars on template (figure 14).
7.
8. Place groove of rear dolly over rim of tank and push until the dolly is tight against bottom
of tank (figure 15).
Secure dolly with screw and washer provided (figure 16).
9.
10. If caster feet are attached together, separate by removing webbing.
11. Take caster foot marked with the letter A and align arrow on foot (figure 17) with arrow
on template also marked with the letter A (figure 18).
12. Place groove of foot over rim of tank and push until the caster foot is tight against
bottom of tank (figure 19).
13. Secure feet with screw and washer provided (figure 20).
14. Insert casters into feet by placing stem of caster into holes provided. Apply pressure and
twisting motion until casters snap into place (figure 21).
15. Place tool basket (not standard with all models), with curved surface against tank, on
rear wheel dolly assembly (figure 22).
10 11
2 3
Template
B A
A B
Bottom of Tank
5
4
A
7
6
11
9
c d e
13
12
Template
B A
A B
Bottom of Tank
15
14
19
Arrow
Tank Bottom
Tank Bottom
(Not standard with all models)
1. With rear of unit facing you, take tool holder and position it with tabs facing rear of unit
(figure 23).
2. Place "J" shaped tabs into the slots on cord wraps (figure 24).
3. Press down until tabs snap into place.
4. Press down on center of tool holder until tab latches on bottom of lid (figure 25).
23
INSTALLING THE CARRIAGE HANDLE
(Not standard with all models)
Attach carriage handle to tank by inserting bolt through the center hole of handle and tank,
secure with nut provided. Attach side handles with screws provided. Be sure to spread ends of
carriage handle when assembling to prevent damage to tank.
3
5
SIDE TANk HANDLE ASSEMBLy
(Not standard with all models)
Attach side handles to tank with screws provided (figure 26).
INSTALLING fOAM SLEEVE AND REUSABLE
(Not standard with all models)
WARNING
WALL OUTLET BEfORE REMOVING THE TANk COVER.
When using the reusable dry filter to pick up dust and dry
material, you must install foam sleeve and reusable dry
filter to ensure proper filtration. If the vacuum has been
used to pick up liquids, the foam sleeve must be cleaned
and dried before installing for dry pick up. With tank cover
in an upside down position, slide foam sleeve down over lid
cage pulling until foam sleeve completely covers lid cage
(figures 27, 28). Center the reusable dry filter on lid cage
(figure 29), slide mounting ring down over filter until ring is
positioned against the ribs of the lid cage (figure 30). The
reusable dry filter should always be in position over the foam
sleeve for dry pick up. To remove the filter for cleaning, remove mounting ring
and filter from lid cage (figure 31). To clean the reusable dry filter, shake off
excess dirt and dust or (depending on the condition of the filter) rinse with water.
Allow the filter to dry completely and reinstall. dO nOT MAChIne WASh OR dRy.
INSTALLING THE CARTRIDGE fILTER
(Not standard with all models)
NOTE: If foam sleeve is in postion over lid cage, it must be removed before installing cartridge
filter.
The cartridge filter can be used for wet or dry pick up; installation is the same for both. When
picking up large quantities of liquid please refer to the Wet Pick up Operation section in this man-
16
17
20 21
22
TOOL HOLDER
24 25
Item Description
1
1 Metal tank handle
2
2 Side tank handle
3 #10 x 3/4" Screw hex head
4 Bolt 1/4 - 20 x 1/2"
4
5 1/4 - 20 Hex nut
DRy PICk UP
DRy fILTER
– ALWAyS DISCONNECT THE PLUG fROM THE
27
29
18
Arrow
A
26
28
30
31