Refrigerator Doors And Drawer - Maytag MFI2570FEZ07 Instrucciones Para El Usuario

3. Turn on water supply to refrigerator and check for leaks.
Correct any leaks.
Complete the Installation
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
1. Plug into a grounded 3 prong outlet.
NOTE: Allow 24 hours to produce the first batch of ice.
Discard the first three batches of ice produced. Allow 3 days to
completely fill the ice container.

Refrigerator Doors and Drawer

All graphics referenced in the following instructions are included
later in this section after "Final Steps."
TOOLS NEEDED: 5/16", 3/8", 1/4" hex-head socket wrench,
#2 Phillips screwdriver, and a flat-blade screwdriver.
IMPORTANT:
Your refrigerator may have a standard reversible refrigerator
■
door with either a freezer door or freezer drawer or French
doors. Follow the instructions specific to the door style of
your model.
All graphics referenced in the following instructions are
■
included later in this section after "Final Steps." The graphics
shown for the standard door are for a right-hand swing
refrigerator (hinges factory installed on the right).
If you only want to remove and replace the doors, see
■
"Remove Door(s) and Hinges" and "Replace Door(s) and
Hinges."
Before you begin, turn the refrigerator control off and remove
■
food and adjustable door or utility bins from the doors.
Remove and Replace Handles
Using a 3/32" or 1/8" hex key, loosen the two setscrews
■
located on the side of each handle. Pull the handle straight
out from the door. Make sure you keep the screws for
reattaching the handles. See Style 1 Handle, graphic 1.
To replace the handles, reverse the directions.
■
To Replace Handles:
1. Position the handle so that the large holes in the mounting
clips are down and align the holes with the door studs.
2. Rotate the handle so that the mounting clips are flat against
the door and slide the handle down to engage. See Handle
graphic.
6
Remove Doors and Hinges
IMPORTANT: Remove food and any adjustable door bins or utility
bins from doors.
WARNING
Electrical Shock Hazard
Disconnect power before removing doors.
Failure to do so can result in death or electrical shock.
1. Unplug refrigerator or disconnect power.
2. Keep the refrigerator doors closed until you are ready to lift
them free from the cabinet.
NOTE: Provide additional support for the refrigerator door
while the hinges are being removed. Do not depend on the
door gasket magnets to hold the door in place while you are
working.
3. Starting with the right-hand side door, remove the parts
for the top hinge as shown in Top Hinges graphic. Lift the
refrigerator door from the bottom hinge pin.
4. Remove top hinge cover from left side refrigerator door.
5. Disconnect the wiring plug located on top of the hinge by
wedging a flat-blade screwdriver or your fingernail between
the two sections. See Connections graphic.
6. Disconnect the water line by pulling back on the locking collar
while pulling the water line out of the water line connector.
See Connections graphic.
7. Remove the parts for the top hinge as shown in Top Hinges
graphic. Lift the left-hand side door from the bottom hinge
pin.
8. Remove the base grille. Grasp the grille firmly and pull it
toward you.
9. Using a 3/8" hex wrench, remove the leveling leg brackets
from the bottom of the cabinet. Keep screws for later use.
Replace Doors and Hinges
1. Assemble the parts for the top hinge as shown in Top Hinge
graphic. Do not tighten the screws completely.
2. Replace the parts for the bottom hinge as shown in Bottom
Hinge graphic. Tighten screws. Replace the refrigerator door.
NOTE: Provide additional support for the refrigerator door
while the hinges are being moved. Do not depend on the
door gasket magnets to hold the door in place while you are
working.
3. Align the door so that the bottom of the refrigerator door
aligns evenly with the top of the freezer drawer. Tighten all
screws.
4. Reconnect the wiring plug on top of the left-hand side
refrigerator door.