Gemini UX-1620 Manual De Funcionamiento página 9

• High sensitivity cardioid capsule for professional use
• Special noise absorption material inside the mic barrel eliminates switch
shock and handling noise
1. Do not drop the microphone element.
2. Do not strike the microphone element with your fist or fingers, and do not
blow strongly into the microphone head front.
3. Do not use the microphone in areas of high humidity and/or high
temperature as this could lead to damage of the microphone.
1. Open the battery holder. Insert 2 AA batteries into the battery holder
according to the polarity indication marked on the battery housing. Close
the battery holder.
2. Push the power switch to the ON position. The BATT indicator should
flash once briefly as you turn on the mic indicating that the mic has
sufficient power. If the BATT stays on, it indicates that the batteries have
insufficient power and should be changed. If the BATT does not light at
all and the mic does not work, it indicates that the batteries are either
dead or not positioned correctly, and you should correct the positioning
or change the batteries. If the microphone is not going to be used for any
length of time, push the power switch to OFF and remove the batteries.
Do not switch the mic on and off rapidly, because you won't get a true
indication from the BATT indicator.
• Heavy duty strain relief
• Foam wind screen
• Tie clip
Note: The lavalier mic clip should be placed on the center of your shirt just
below your collarbone.
• Heavy duty strain relief
• Headset
• Foam wind screen
1. Open the battery door by sliding towards the arrow. Insert 2 AA batteries
into the battery holder according to the polarity indication marked on the
battery housing. Close the battery door.
2. Connect the mic to the belt pack transmitter.
3. Push the power switch to the ON position. The LOW BATT indicator
should flash once as you turn on the belt pack indicating that the
transmitter has sufficient power. If the LOW BATT stays on, it indicates
that the batteries have insufficient power and should be changed. If the
LOW BATT does not light at all, it indicates that the batteries are either
dead or not positioned correctly, and you should correct the positioning
or change the batteries. If the microphone is not going to be used for any
length of time, push the power switch to OFF and remove the batteries.
4. To adjust the gain (input sensitivity), place the small plastic tool (included
with the unit) in the hole marked gain on the side of the belt pack and
slowly turn the tool and speak into the mic until the volume is adjusted.
Use of any other tool to adjust the gain will void the warranty.
Hint: If the audio signal's sound is distorted, try turning the gain down on
your belt pack transmitter and/or your mixer, and increase the volume
output on the receiver.
EUROPE
Frequency Range........................................................863.125 ~ 864.875 MHz
Receiving System..................................................................PLL Synthesized
Receiving Mode............................................................................dual channel
Frequency Stability.............................................................................± 0.005%
Signal to Noise Ratio.............> 94 dB @ 15 kHz and 60 dBµV antenna input
Dynamic Range.....................................................................................> 96dB
AF Response..............................................................40 Hz - 15 kHz (±3 dB)
T.H.D......................................................................................< 1.0% @ 1 kHz
Audio Output......................................unbalanced; 0 dB (0 dB=0.775V) at
Power Supply.............................................................................D.C. 12~18 V
Dimensions.......................2" (H) x 8.27" (W) x 6.5" (D) (51 x 210 x 166 mm)
Frequency Range.........................................................863.125 ~ 864.875 MHz
RF Power Output...........................................................................30 mW max.
Oscillation Mode..................................................................PLL Synthesized
Frequency Stability............................................................................± 0.005%
T.H.D......................................................................................<0.5% @ 1 kHz
LED Indicator.................................................Power ON-OFF and low battery
Current Consumption...............................................................65 mA @ 2.4V
Batteries.................................................................................................2 AA
Microphone Element...........................................................................Dynamic
Dimensions.................................................10.7" (L) x 2.4" (D) (272 x 62 mm)
Microphone Element....................................................................Condenser
Dimensions...................................4" (H) x 2.6" (W) x 1" (D) (98 x 66 x 25 mm)
Page 2
48 kHz reference RF deviation
balanced; -20 dB (0 dB=0.775V)
EUROPE