Rear Panel - Fender BASSBREAKER 007 Manual De Instrucciones

INPUT POWER
120V 60Hz
55W
フェンダー·
ミュージック(株)
TYPE: PR 3032
FUSE
SERIAL NUMBER
F2A L
250V
H. FUSE: Provides electrical over-current protection. With power
disconnected, replace a blown fuse only with one of the type
and rating specified on the amp's rear panel.
I. IEC POWER INLET: Using the included power cord, connect
to a grounded outlet in accordance with the INPUT POWER
voltage and frequency specified at the power inlet.
J. SPEAKER OUTPUT: Connect external speaker cabinet here (8Ω
minimum). On Bassbreaker 007 combo model, use of this jack
automatically disconnects internal speaker.
To avoid damaging the amp, turn it off (G) when changing
!
speaker connection.
TYPE
POWER
INPUT IMPEDANCE
SPEAKER (INTERNAL)
EXTERNAL SPEAKER ENCLOSURE
TUBES
LINE OUT
ACCESSORIES
DIMENSIONS (COMBO)
WEIGHT (COMBO)
DIMENSIONS (HEAD)
WEIGHT (HEAD)

Rear Panel

7 WATTS
8Ω MIN
SPEAKER LINE
OUTPUT OUTPUT
COMBO ONLY:
MUTES
INTERNAL SPEAKER
Specifications
PR 3032
Requirements: 55 watts
1MΩ
One 10" Celestion® Ten Thirty (8Ω, PN 7700223000)
Bassbreaker BB-112 (optional, PN 226700000, contains one 12" 8Ω Celestion® speaker)
V1: 7025/12AX7A/ECC83
Output impedance: 100Ω
Single-button footswitch (optional, PN 7706424000)
Width: 15.81" (40.2 cm)
25.5 lbs. (11.5 kg)
Width: 15.81" (40.2 cm)
16.6 lbs. (8 kg)
Product specifications subject to change without notice.
BASSBREAKER 007
FENDER MUSICAL INSTRUMENTS CORP.,
CAUTION:
CHASSIS SURFACE HOT
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS EQUIPMENT TO RAIN OR MOISTURE
AVERTISSEMENT:
AT T E N T I O N :
S U P E R F I C I E D E C H A S S I S C H A U D E
FOOT
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE BACK COVER.
SWITCH
NO USER SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED PERSONNEL ONLY.
WARNING:
FENDER AMPLIFIER SYSTEMS ARE CAPABLE OF PRODUCING VERY
HIGH SOUND PRESSURE LEVELS WHICH MAY CAUSE TEMPORARY OR PERMANENT HEARING
DAMAGE. USE CARE WHEN SETTING AND ADJUSTING VOLUME LEVELS DURING USE.
K. LINE OUTPUT: Provides a line-level signal with tone shaping
from the preamp. Power amp distortion, if any, will be included
in this signal, which can be sent to effects devices such as delay
or chorus units and to the effects loop or power amp input of
another amplifier. Signal is also suitable for external recording
interfaces and sound reinforcement equipment (note that this
offers no speaker emulation).
L. FOOTSWITCH: Connect optional single-button TREBLE
BOOST (B) footswitch here.
For questions and troubleshooting, contact a Fender
specialist at:
1-800-856-9801 (U.S. toll free)
1-480-596-7195 (International)
Output: 7 watts into 8Ω
V2: 7025/12AX7A/ECC83
Combo cover (optional, PN 7707881000)
Height: 14.75" (37.5 cm)
Height: 8.94" (22.7 cm)
TM
A PRODUCT OF:
CORONA, CA U.S.A.
MADE IN MEXICO
RISQUE DE CHOC ELECTRIQUE ! NE PAS OUVRIR !
V3: 6BQ5/EL84
Amp head cover (optional, PN 7707882000)
Depth: 8.5" (21.6 cm)
Depth: 8" (20.3 cm)
CAUTION:
TO RE
REPLACE FUSE WITH S
WAR
MAINTAIN 6
FOR VEN
3