Planer Safety Warnings - Makita 1100 Manual De Instrucciones

ENGLISH
1 Knob
2 Switch trigger
3 Lock button/Lock-off button
4 Bolt
5 Drum
6 Planer blade
7 Drum cover
8 Adjusting plate
9 Inside edge of gauge plate
10 Blade edge
11 Screws
12 Heel
13 Back side of gauge base
14 Gauge plate
15 Gauge base
SPECIFICATIONS
Model
Planing width ........................................................ 82 mm
Planing depth ......................................................... 3 mm
Shiplapping depth ................................................ 20 mm
–1
No load speed (min ) .......................................... 16,000
Overall length ..................................................... 415 mm
Net weight ............................................................. 5.1 kg
Safety class ..............................................................
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for planing wood.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.

PLANER SAFETY WARNINGS

1. Wait for the cutter to stop before setting the tool
down. An exposed cutter may engage the surface
leading to possible loss of control and serious injury.
2. Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body
leaves it unstable and may lead to loss of control.
3. Rags, cloth, cord, string and the like should
never be left around the work area.
6
Explanation of general view
16 Pan head screw
17 Planer blade locating lugs
18 Heel of adjusting plate
19 Set plate
20 Inside flank of gauge plate
21 Mini planer blade
22 Groove
23 Hex. flange head bolt
24 Drum cover
25 Makita vacuum cleaner
26 Standard (non-round) chip
cover
27 Start
28 End
29 Cutting line
4.
1100
5.
6.
7.
8.
9.
/II
10. Make sure the blade is not contacting the work-
11. Wait until the blade attains full speed before cut-
12. Always switch off and wait for the blades to
13. Never stick your finger into the chip chute.
14. Do not leave the tool running. Operate the tool
15. Always change both blades or covers on the
GEA010-1
16. Use only Makita blades specified in this manual.
17. Always use the correct dust mask/respirator for
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
GEB010-3
to safety rules for the subject product.
MISUSE or failure to follow the safety rules stated in
this instruction manual may cause serious personal
injury.
30 Screw
31 Edge fence
32 V groove
33 Sharpening holder
34 Wing nut
35 Blade (A)
36 Blade (B)
37 Side (C)
38 Side (D)
39 Limit mark
40 Chip cover
41 Screwdriver
42 Brush holder cap
Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
Use only sharp blades. Handle the blades very
carefully.
Be sure the blade installation bolts are securely
tightened before operation.
Hold the tool firmly with both hands.
Keep hands away from rotating parts.
Before using the tool on an actual workpiece, let
it run for a while. Watch for vibration or wobbling
that could indicate poor installation or a poorly
balanced blade.
piece before the switch is turned on.
ting.
come to a complete stop before any adjusting.
Chute may jam when cutting damp wood. Clean
out chips with a stick.
only when hand-held.
drum, otherwise the resulting imbalance will
cause vibration and shorten tool life.
the material and application you are working
with.