Functional Description - Makita CV101D Manual De Instrucciones

battery pack may create a risk of fire when used with
another battery pack.
• Use the vest only with specifically designated battery
packs. Use of any other battery packs may create a risk
of injury and fire.
• Before using battery cartridge, read all instructions and
cautionary markings on (1) battery charger, (2) battery,
and (3) product using battery.
• Do not disassemble battery cartridge.
• If operating time has become excessively shorter, stop
operating immediately. It may result in a risk of
overheating, possible burns and even an explosion.
• Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If electrolyte gets into your
eyes, rinse them out with clear water and seek medical
attention right away. It may result in loss of your
eyesight.
• Do not short the battery cartridge:
1. Do not touch the terminals with any conductive
material.
2. Avoid storing battery cartridge in a container with
other metal objects such as nails, coins, etc.
3. Do not expose battery cartridge to water or rain.
A battery short can cause a large current flow,
overheating, possible burns and even a breakdown.
• Do not store the vest, battery holder and battery
cartridge in locations where the temperature may reach
or exceed 50°C (122°F).
• Do not incinerate the battery cartridge even if it is
severely damaged or is completely worn out. The
battery cartridge can explode in a fire.
• Be careful not to drop or strike battery.
• Do not use a damaged battery.
• Follow your local regulations relating to disposal of
battery.
Tips for maintaining maximum battery life
• Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
• Charge the battery cartridge with room temperature at
10°C - 40°C (50°F - 104°F).
• Let a hot battery cartridge cool down before charging it.
• Charge the battery cartridge if you do not use it for a
long period (more than six months).
• For an optimum life-time, the battery cartridge have to
be fully charged, after use.
SAVE THESE INSTRUCTIONS.
DESIGNATION OF PARTS (Fig. 1)
1. Power button
2. Battery holder pocket (Backside)
3. Power cable (Inside the battery holder pocket)
4. Hole for strap
5. Battery holder
(See the last part of this instruction manual for all the
illustrations.)
4
SPECIFICATIONS
Model
Temperature adjustment
steps
Material
USB power supply port
Operating time (h)
Low
Medium
High
Rated voltage (V)
Battery cartridge
• Due to our continuing program of research and
development, the specifications herein are subject to
change without notice.
• Specifications and battery cartridge may differ from
country to country.
• Operating time may differ depending on battery type
and usage condition.

FUNCTIONAL DESCRIPTION

Switch action
To turn on the vest, push and hold the power button
(about 1.5 seconds). To turn off, push and hold the power
button again.
Temperature adjustment
There are three temperature settings (high, medium, low).
Three LED lights means that the temperature is set to
"high", two LED lights "medium", and one LED light "low".
When you switch on the vest, the temperature is set to
"high". Each press of the power button cycles through the
vest's temperature setting.
Indicating the remaining battery capacity
(Fig. 2)
(Only for battery cartridges with "B" at the end of the
model number.)
Press the check button (7) on the battery cartridge to
indicate the remaining battery capacity. The indicator
lamps (6) light up for few seconds.
CV101D
3
Shell and lining:
- Nylon 100%
Side:
- Polyester 90%
- Spandex 10%
Armhole circumference & Fill:
- Polyester 100%
DC 5V, 2.1A
With battery BL1040B
APPROX. 14
APPROX. 7.5
APPROX. 4.0
DC 10.8 V
BL1015, BL1020B, BL1040B