Craftsman 351.184090 Manual Del Operador página 2

Warranty ....................................... 2
Safety Rules .................................... 2
Operation .................................... 2-4
Maintenance .................................... 4
Troubleshooting ................................. 5
Parts Illustration and List ......................... 6-7
EspaSol ..................................... 8-11
FULL ONE YEAR WARRANTY ON CRAFTSMAN
AIR-DRIVE TOOLS
If this Craftsman air-drive tool fails due to a defect in material
or workmanship within one full year from the date of
purchase, return it to the nearest Sears Service Center in the
United States, and Sears will repair it free of charge.
If this air-drive tool is used for commercial purposes, this war-
ranty applies for only 90 days from the date of purchase.
This warranty gives you specific legal rights and you may also
have other rights which vary from state to state.
Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL
60179
• Air tool operators and all others in work area should
always wear safety goggles complying with United States
ANSI Z87.1 to prevent eye injury from fasteners and flying
debris when loading, operating or unloading this tool.
• Never exceed operating pressure of 100 PSI.
• Always keep hands and body away from the fastener dis-
charge area when air supply is connected to tool.
• Always disconnect tool from air supply when servicing or
adjusting tool and when tool is not in use.
• Do not operate when contact trip is not in contact with
work.
• Never load the tool until you are ready to use it.
• Never depress tool trigger when loading.
• Always load with nose of tool pointing away from you and
others.
• Never point tool at yourself or others.
• Never carry tool with trigger depressed.
• Do not use oxygen, combustible gas or high pressure
compressed gas as the air supply for the tool.
• Always use tool at safe distance from other people in work
area.
• Do not attempt to discharge fastener into hard or brittle
materials such as concrete, steel or tile.
• Do not connect female quick-disconnect coupling to tool
side of air line.
• Connect male, free-flow nipple to tool side of air line so
that tool is depressurized when hose is disconnected.
• Do not use a hose swivel with this tool.
• Use Sears recommended fasteners only.
DESCRIPTION
The Craftsman 18 Gauge Brad Nailer drives brads from 3/8" to
1_/4"long. Oilless design eliminates daily oiling and oil stains
on workpiece. Die cast aluminum body with textured grip mini-
mizes operator fatigue. Large capacity, side loading magazine
with positive, quick action latch makes loading easy. Safety
feature disables tool unless contact trip is pressed against
workpiece. Tapered nosepiece provides operator with greater
visibility for precise fastener placement. Rigid nosepiece
reduces jamming. The 18 Gauge Brad Nailer is excellent for
molding, furniture making, and picture framing.
SPECIFICATIONS
Capacity ............................. 110 brad nails
Nail size ..................... 18 gauge (.049" x .040")
Nail lengths ............................... % to 1_"
Operating pressure ....................... 60-100 PSI
Air inlet .................................. '/4" N.ET.
Length ....................................... 9"
Height ....................................... 7_ ''
Width ........................................ 2"
Weight ..................................... 2 Ibs.
BRAD NAILS
18341 .................... 18 gauge brad nails, %" long
18342 .................... 18 gauge brad nails, 1" long
18343 ................... 18 gauge brad nails, 1'/4" long
AIR SUPPLY LINE
Refer to Figure 1 (page 3).
° The air tool operates on compressed air at pressures from
60 to 100 PSI.
° Never exceed maximum pressure.
Air Delivery Required: 0.47 SCFM @ 90 PSI
(30 shots per minute).
WARNING: Keep hands and body away from discharge area
of tool when connecting air supply. Always disconnect tool
from air supply when servicing or adjusting tool and when tool
is not in use.
° Air operated tools require clean, dry, compressed air to
ensure top performance, low maintenance and long life.
° Dirt and abrasive materials present in all air lines will
damage tool O-rings, valves and cylinders.
° Moisture will reduce tool performance and life if not
removed from compressed air.
° A filter-regulator system is required and should be located
as close to tool as possible (see Figure 1, page 3). A dis-
tance of less than 15 feet is recommended.
° Keep air filter clean. A dirty filter will reduce the air pressure
to the tool causing a reduction in power and efficiency.
° The air supply system must be able to provide air pressure
of 60 to 100 pounds per square inch at tool.
° All hoses and pipes in the air supply system must be clean
and free of moisture and foreign particles.
° Do not mount swivel connector in air supply line.
° The air pressure should be properly regulated.
2