Cameo CLP56Q8W Manual De Usuario página 14

COLOUR MACROS
In this mode, one of the 4 basic colours of the projector or one of the 11 different mixed colours can be selected as a preset. Press the MODE button
repeatedly until "CMXX" appears on the display. Now press ENTER and then select one of the 15 colour presets using the UP and DOWN buttons.
Confirm with ENTER.
CM01 = Red
CM02 = Green
CM03 = Blue
CM04 = White
CM05 = Yellow
CM06 = Cyan
CM07 = Magenta
CM08 = Pink
COLOUR CHANGE
In the colour change mode (Jumping Mode), different colours are blended into one another in succession. The speed of the program is adjustable
separately and a stroboscope effect can also be activated.
Press the MODE button repeatedly until "JXXX" appears in the display.
To adjust the speed of the colour change, press ENTER (the 2nd digit on the display flashes) and then use the UP and DOWN buttons to select the
desired speed in the "JUXX" menu. Now, press ENTER again (the last two digits on the display will flash) and using the UP and DOWN buttons, select
the speed with which the colours should alternate, from JU00 to JU99. Confirm with ENTER.
To activate and adjust the strobe effect, press ENTER (the 2nd digit on the display flashes) and then use the UP and DOWN buttons to select the
desired strobe effect in the "JFXX" menu. Now, press ENTER again (the last two digits on the display will flash) and using the UP and DOWN buttons,
select the strobe speed JF00 to JF99 (JF00 = strobe effect deactivated, approx. 1 Hz = JF01, JF99 = approx. 20 Hz). Confirm with ENTER.
Colour change
Stroboscope
COLOUR BLENDING
In the colour fade mode (Fading Mode) different colours are blended into one another in succession. The speed of the program is adjustable sepa-
rately and a stroboscope effect can also be activated.
Press the MODE button repeatedly until "FXXX" appears in the display.
To adjust the speed of the colour fade, press ENTER (the 2nd digit on the display flashes) and then use the UP and DOWN buttons to select the
desired speed in the "FAXX" menu. Now, press ENTER again (the last two digits on the display will flash) and using the UP and DOWN buttons, select
the speed with which the colours fade, from FA00 to FA99. Confirm with ENTER.
To activate and adjust the strobe effect, press ENTER (the 2nd digit on the display flashes) and then use the UP and DOWN buttons to select the
desired strobe effect in the "FFXX" menu. Now, press ENTER again (the last two digits on the display will flash) and using the UP and DOWN buttons,
select the strobe speed from FF00 to FF99 (FF00 = strobe effect deactivated, approx. 1 Hz = FF01, FF99 = approx. 20 Hz). Confirm with ENTER.
Colour fading
Stroboscope
AUTO MODE
Press the MODE button repeatedly until "AUTO" appears on the display. In this operating mode, the light switches automatically between colour
change and colour fading mode. The speed of the individual effects is determined by the settings of the respective mode.
SLAVE MODE
Press the MODE button repeatedly until "SLAV" appears on the display. Connect the slave and master unit of the same type with a DMX cable
(master unit DMX OUT - slave unit DMX IN). Now the slave unit follows the master unit.
MUSIC CONTROL
Press the MODE button repeatedly until "SUXX" appears on the display.
Now the projector is controlled by the built-in microphone and follows the beat of the music. To adjust the microphone sensitivity, press ENTER (the
last two digits on the display will flash) and use the UP and DOWN buttons to set the desired value from SU00 to SU99 (SU00 = minimum sensitivity,
SU99 = maximum sensitivity). Confirm with ENTER.
14
CM09 = Light Green
CM10 = Lavender
CM11 = Light Pink
CM12 = Light Yellow
CM13 = Light Magenta
CM14 = Light Cyan
CM15 = Warm White
Speed JU00 - JU99
Speed JF00 - JF99
Speed FA00 - FA99
Speed FF00 - FF99