Power Supply; Setting Into Operation - Monacor security TFT-1700COL Manual De Instrucciones

3. The wire which is coloured brown must be con-
GB
nected to the terminal which is marked with the
letter L or coloured red.
Warning – This appliance must be earthed.
If the units are to be put out of operation
definitively, take them to a local recycling
plant for a disposal which is not harmful to
the environment.
3 Applications
This TFT LCD colour monitor with extra short response
time and very high-contrast picture reproduction is
especially suitable for applications in surveillance sys-
tems, however, it can also be used for other purposes,
e. g. as a PC monitor or for multimedia applications.
Up to 4 signal sources (e. g. surveillance camera,
video recorder, PC, DVD player) can be connected to
the monitor. Feed-through outputs allow to pass on the
input signals to other units. Via an on-screen menu the
monitor can be adjusted in an optimum way to the
requirements of the respective application.
4 Setting-up
To prevent disturbing reflections, place the monitor via
the base fixed to its rear side so that no light directly
falls on the screen surface. To obtain a favourable
viewing angle, the monitor can slightly be inclined for-
ward or backward.
5 Connection
5.1 Units with composite signal or S-Video signal
5.1.1 Connecting the signal sources
1) Two signal sources may be connected which supply
composite video signals, e. g. surveillance cam-
eras, video recorders:
– Connect the video output of the first source to the
BNC input jack VIDEO 1 (10) and the video out-
put of the second source to the BNC input jack
VIDEO 2 (18).
– Connect the audio output of the first source to the
phono input jacks AUDIO 1 (8) and the audio out-
put of the second source to the phono input jacks
AUDIO 2 (16) [red = right channel, white = left
channel].
2) The video output of a signal source which supplies
an S-Video signal, e. g. digital recorder, DVD player,
may be connected to the 4-pole mini DIN input jack
S-VIDEO (12). Connect the audio output of the
source to the phono input jacks AUDIO 1 (8) [red =
right channel, white = left channel].
5.1.2 Feed-through outputs
Via the feed-through outputs it is possible to pass on
the respective input signal e. g. to another monitor or to
a recorder:
10
– audio output AUDIO 1 (9) and video output VIDEO 1
(11) to feed through the signals of audio input
AUDIO 1 (8) and of video input VIDEO 1 (10)
– video output S-VIDEO (13) to feed through the
signal of video input S-VIDEO (12)
– audio output AUDIO 2 (17) and video output
VIDEO 2 (19) to feed through the signals of audio
input AUDIO 2 (16) and of video input VIDEO 2 (18)
Connect the respective output to the corresponding
input of the following unit.
5.2 PC
Connect the VGA output of the PC to the 15-pole D-Sub
jack VGA (14) and its audio output to the 3.5 mm jack
PC AUDIO (15).
Important: Resolution and picture frequency of the PC
graphics card have to be adapted to the monitor. The
following combinations are compatible:
Frequency 60 Hz 66 Hz
Resolution
640 x 480 √
800 x 600 √
1024 x 768
√
1280 x 1024 √
For an optimum picture reproduction the PC graphics
card should be adjusted to a resolution of 1280 x 1024
and a picture frequency of 60 Hz.

5.3 Power supply

After connection of all units, connect the supplied
power supply unit to the jack DC 12V (7) and to a socket
(100 – 240 V~/50 – 60 Hz) via the supplied mains cable.
Note: The monitor has a low current consumption even
in stand-by operation. If it is not used for a longer time,
the power supply unit should be disconnected from the
power supply to save energy.

6 Setting into Operation

After connection of the power supply the monitor is
switched on [power LED (1) shows green] and repro-
duces picture and sound of the signal source last se-
lected. On the top left of the picture its identification is
shortly inserted:
BNC1: source at the input VIDEO 1 (10)
BNC2: source at the input VIDEO 2 (18)
S-VIDEO: source at the input S-VIDEO (12)
PC: source at the input VGA (14)
To stop the reproduction, press the button
the monitor is switched to stand-by, the power LED
shows red. To switch on press the button .
Note if video signal is missing/video loss
The monitor only reproduces the sound of a source if it
receives a video signal from this source. If the monitor
switched on does not receive a video signal from the
selected source, "NO SIGNAL OR SIGNAL LOSS" is
inserted for approx. 15 seconds. Then the monitor is
switched to stand-by, the power LED flashes red.
70 Hz 72 Hz 75 Hz
√ √ √ √
√ √ √ √
√ √ √
(6). Then
85 Hz
√
√
√